Publicidad
Idiomas disponibles
Idiomas disponibles
4.1.1 WORK POSITION
THE OPERATOR MUST BE SEATED IN THE DRIVING SEAT
OF THE TRACTOR WHEN THE MACHINE IS WORKING SINCE
ONLY FROM THAT POSITION IS HE ABLE TO ACT COR-
RECTLY. BEFORE HE LEAVES THE DRIVING SEAT, THE OP-
ERATOR MUST STOP THE MACHINE, APPLY THE PARKING
BRAKE AND TURN OFF THE TRACTOR ENGINE.
4.2 HITCHING TO THE TRACTOR
Hitching to the tractor could be a dangerous operation. Take
great care and strictly comply with the instructions.
Proceed in the following way to hitch the machine to the tractor in
the correct way:
- Make sure that you are using a tractor whose configuration suits
the machine in question.
- Make sure that there are no objects, bystanders and/or animals
in the immediate vicinity of the machine and that the PTO is
disengaged.
- Make sure that the machine is in a stable, horizontal position,
then back up the tractor towards the machine.
- Having reached the right position, turn off the tractor engine
then fit the driveline first into the PTO of the machine and then
to the tractor PTO. Make sure that it is firmly locked in position.
- Move the power lift bars near and fit them into the plates. Insert
the plug and lock in place with the supplied split pins.
Since the power lift links of each tractor are a certain length
and have a hole of a certain diameter, you must find the most
suitable position for the tractor you use by inserting the pins
into the relative holes according to your needs and depending
on the diameter (Fig. 6).
- Lock the power lift bars with the relative chains and idlers par-
allel to the tractor. This must be done to prevent the machine
from swinging sideways.
- Insert the driveline and make sure that it is perfectly locked on
to the tractor PTO. Check that the guard is free to turn. Fix the
driveline shield with the relative chain. Remove the driveline
support (16 Fig. 1) and fix it to the relative hitch on the linkage.
Take the utmost care when you insert the driveline. Make
sure that it is firmly locked on to the tractor PTO and on the
machine. Also comply with the indications in the instruction
manual supplied with each driveline. Make sure that the driv-
eline shield, fixed with the relative chains, is free to turn with-
out obstructions. Also check the protective shields on the
tractor and on the implement. If some guard is not in perfect
working order, it must be immediately replaced with a new
guard. It is very important to ensure that the protective shields
on both sides overlap the driveline ones by at least 5 cm.
- Connect the upper third point and adjust the top link in the cor-
rect way, making sure that the upper surface of the machine is
parallel to the ground. This is very important as parallelism be-
tween the axis of the machine and that of the tractor PTO is
obtained in this way.
- The spring ram (optional) supports the levelling plate and
dampens the vibration transmitted during road transport. It also
prevents the machine from overturning when it is parked.
DANGER
DANGER
DANGER
b 53 s
The following expressions must be observed to ensure that
the tractor-machine assembly is stable (Fig. 8):
M x s < 0,2T x i + Z (d + i)
M < 0,3T
Z>{[(M x s)-(0,2T x i)]/(d x i)} (for calculating the ballast)
where:
i = tractor's wheelbase
d = horizontal distance between the center of gravity of the
front ballast and the tractor's front axle
s = horizontal distance between the center of gravity of the
machine and the tractor's rear axle
T = weight of the tractor in running order
Z = ballast weight
M = weight of the machine.
4.3 DRIVELINE
The driveline is a mechanical component. When it is operating
it can be a source of danger to the physical well-being of those
who work with it. Take the greatest care when carrying out
operations that involve the driveline. Carefully read the instruc-
tion manual supplied with the driveline. If you have doubts about
the way it operates, if it is without its shields, worn or broken,
replace it with a new driveline bearing the "CE" mark.
Never modify or adapt the driveline in any way. If this is nec-
essary, contact your nearest Authorized Assistance Center.
Since the driveline spins at high speed, it is balanced during the
testing phase.
Any successive interventions could therefore lead to lack of bal-
ance which could then impair the functionality of the machine
besides that of the actual driveline itself.
The angle at which the driveline works must be the minimum pos-
sible as this will ensure that both the driveline and machine are
long-lasting.
When the driveline is fully extended, in all work conditions, the
telescopic tubes must overlap to at least 1/3rd of their length (A
Fig. 5).
When the driveline is fully inserted, the play must be at least 4 cm
(B Fig. 5).
Contact the Manufacturer's Technical Service if this is not pos-
sible.
Before engaging the PTO, make sure that its rotation speed
corresponds to the rate for which the machine has been de-
signed (540 or 1000 rpm).
4.3.1 DRIVELINE WITH ADJUSTABLE PLATE
CLUTCH
The driveline has a safety clutch to protect the transmission com-
ponents of the machine against stress and excessive overloads.
The clutch is calibrated for medium-duty use. If it slips during
work, all the nuts that hold the springs must be evenly tightened
by half a turn and the operation of the device checked after about
200 meters of work. Repeat the operation if necessary. The clutch
must be adjusted by unscrewing the nuts if it is blocked.
- 19 -
(prudential value)
DANGER
DANGER
CAUTION
Publicidad
