cecotec BOLERO COOLMARKET COMBI 322 WD INOX D Manual De Instrucciones página 35

ENGLISH
B. Additional parts (included in the plastic bag)
13. Upper-left hinge
14. Upper-left hinge cover
15. Right-hand screw gap cover
16. Middle-left hinge
17. Left unblocker *2
18. Left doorstop *2
19. Allen key (4 mm)
Fig. 7
1. Self-tapping screw
2. Upper-right hinge cover
3. Electrical connector
4. Door switch
Fig. 8
5. Upper-left hinge cover
Fig. 9
6. Screws
7. Upper-right hinge
8. Electrical connector
Fig. 11
9. Right-hand screw gap cover
10. Left-hand screw gap cover
Fig. 12
11. Upper-left side door cover
12. Left-hand door connector
13. Upper-right side door cover
14. Right-hand door connector
Fig. 13
15. Right-hand upper door stop
16. Right-hand upper door dowel
17. Self-tapping screw
18. Left-hand upper door stop
19. Left-hand upper door dowel
Fig. 15
20. Right-hand lower door stop
68 B O LE R O COOLM ARKET COM BI 3 2 2 WH ITE/INOX/ DAR K D
B O LE R O COOLM ARKET COM BI 3 2 2 WD INOX D
B O LE R O COOLM ARKET COM BI 3 2 2 GLASS WH ITE/BL ACK/GREY D
21. Right-hand lower door dowel
22. Self-tapping screw
23. Left-hand lower door stop
24. Left-hand lower door dowel
Fig. 17
25. Lower hinge
26. Special flange screw
27. Adjustable lower legs
Fig. 18
28. Lower hinge pin
Fig. 21
29. Upper door's upper-left hinge
Fig. 22
30. Upper door connector
31. Refrigerator connector
32. Refrigerator connector
Fig. 23
33. Self-tapping screw
1. Open the door, remove the door shelves (to prevent any damage) and then close the door.
To remove the shelves, slightly press the shelf and move it upwards. Fig. 6
2. Unscrew the screw on the upper-right hinge (1), then remove the upper hinge cover (2).
Carefully unplug the electrical connector (3) underneath. Fig. 7
3. Press the side of the door switch (4) and pull it upwards to separate it from the upper-right
hinge cover (2). Insert the door switch (4) into the upper-left hinge cover (5) (included in
the plastic bag). Keep the upper-right hinge cover (2). Fig. 8
4. Unplug connectors (A) and (B). Then unscrew the screws (6) with an 8 mm drill or a
spanner and remove the upper-right hinge (7). Then fit the connectors (A) and (B) into
the hole as shown in figure 9. After this process, the refrigerator door will be unstable. Be
sure to hold it in place so as not to damage it. Fig. 9
5. Carefully lift the upper door to remove it from the middle hinge. Then place the upper door
on a soft surface with the inside facing upwards. Fig. 10
6. Insert the right-hand screw gap cover (9) (included in the plastic bag) into the upper-right
side where the upper-right hinge was located. Then, remove the left screw gap cover (10)
from the upper-left side of the refrigerator and put it away. Fig. 11
7. Remove the upper-left side door cover (11) and remove the connector (12). Remove the
B OLERO COO LMA RKET COMB I 322 W HITE/ IN OX/DA RK D
BOLERO COOLMARKET COMBI 322 WD IN OX D
BOL ERO CO OLMARKET CO MBI 322 GLAS S W HITE/B LACK/GREY D
ENGLISH
69