Publicidad
Idiomas disponibles
Idiomas disponibles
Other Connectors
ETHERNET
OUTPUT1
ZONE2
Serial connector
OUTPUT2
PVR
UHD
eARC
OUT
USB 5V/0.5A
GAME
STB
WI-FI
HDMI
RS232 serial connector
AV
BD
PVR
CD
SAT
PVR
WI-FI
HEIGHT2
BLUETOOTH
HEIGHT1
Z2 OUT
LINE OUT
STB
FM/DAB
L
TRIG Z1
Z1 IR
R
RS232
ANALOGUE AUDIO
BD
CD
CH13/14
CH15/16
TRIG Z2
Z2 IR
L
SPEAKER OUTPUTS
SUB2
ZONE2 L
8Ω LOAD IMPEDANCE RECOMMENDED
R
HEIGHT1 L
SR
FR
C
FL
SL
SBL
The connector is used with control devices having an RS232
PREAMP OUT
serial port (for example, Crestron and AMX touch-screen
PREAMP OUT
controllers).
FL
SL
C
SBL
Network connector
SBL
SR
FR
C
FL
SL
HEIGHT1 L
SUB1
SBR
Networking is a large subject and only the briefest guidelines
FR
SR
ZONE2 L
are presented in this handbook. Please contact your Arcam
CAMBRIDGE, CB25 9PB, UK
DESIGNED IN THE UK
dealer or specialist installer for more information about
MADE IN VIETNAM
introducing the Receiver into your computer network.
ETHERNET
OUTPUT1
eARC
USB 5V/0.5A
WI-FI
HEIGHT2
HEIGHT1
Z2 OUT
LINE OUT
STB
GAME
AV
L
Ethernet
R
If an Ethernet cable is connected, the Receiver will
ANALOGUE AUDIO
CH13/14
CH15/16
automatically attempt to connect to your network.
L
SUB2
You should use CAT5 cable plugged into the RJ45 socket
ZONE2 R
R
HEIGHT1 R
SR
labelled
on the rear panel.
SBR
PREAMP OUT
If your network uses static IP addressing rather than DHCP,
PREAMP OUT
you will need to provide IP address, gateway and DNS; see
FL
SL
C
SBL
page EN-34 for information on setting up the network.
USB connector
SBR
SR
FR
SR
SUB1
SBR
HEIGHT1 R
ZONE2 R
The Receiver can be updated via the USB socket on the rear
of the unit, if no network connection and so "Over The Air"
update is not available.
OUTPUT1
ZONE2
BD
SAT
AV
Trigger connectors
GAME
STB
OUTPUT2
PVR
UHD
eARC
OUT
WI-FI
DIGITAL AUDIO
GAME
AV
BD
PVR
TRIG Z1
CD
Z1 IR
FM/DAB
RS232
TRIG Z2
Z2 IR
STB
ANALOGUE AUDIO
AV
OUT
SPEAKER OUTPUTS
ZONE2 R
ZONE2 L
8Ω LOAD IMPEDANCE RECOMMENDED
HEIGHT1 R
HEIGHT1 L
SR
FR
C
FL
SL
SBR
SBL
The trigger connectors (
electrical signal whenever the Receiver is switched on and
the relevant zone enabled.
SBL
SBR
SR
FR
The trigger signal can be used to switch on and off
C
FL
SL
HEIGHT1 L
HEIGHT1 R
CAMBRIDGE, CB25 9PB, UK
ZONE2 L
ZONE2 R
DESIGNED IN THE UK
compatible pieces of home entertainment equipment, for
example, you could set up a trigger to turn on your television
and BD player whenever the Receiver was switched on.
There are two trigger output sockets on the Receiver, each
capable of outputting a 12V, 70mA switching signal. The
ZONE2
OUTPUT2
PVR
UHD
BD
OUT
socket is designed for mono 3.5mm jacks: tip is the trigger
output, sleeve is ground.
HDMI
DIGITAL AUDIO
BD
PVR
CD
SAT
PVR
FM/DAB
TRIG Z1
Use for remotely turning on and off power amps or source
equipment for Zone 1. On = 12V, Off = 0V.
BD
CD
STB
SPEAKER OUTPUTS
TRIG Z2 (AVR21, AVR31, AV41)
ZONE2 L
8Ω LOAD IMPEDANCE RECOMMENDED
HEIGHT1 L
FR
C
FL
SL
Use for remotely turning on and off power amps or source
SBL
equipment for Zone 2. On = 12V, Off = 0V.
SBL
C
FL
SL
FR
HEIGHT1 L
ZONE2 L
Infrared (IR) connectors
BD
SAT
AV
GAME
STB
BLUETOOTH
HDMI
DIGITAL AUDIO
SAT
PVR
TRIG Z1
Z1 IR
tip: Trigger output
RS232
sleeve: Ground
TRIG Z2
Z2 IR
BD
CD
STB
AV
OUT
and
) provide an
The infrared inputs (
external IR receivers, either when the Receiver front panel IR
receiver is fully or partially obstructed or to allow the use of a
remote control in Zone 2.
MADE IN VIETNAM
There are two IR inputs on the Receiver, each designed for
stereo or mono 3.5mm jacks. Tip is the modulated signal,
sleeve is ground.
Z1 IR
SAT
AV
GAME
STB
This input is intended for use with a local IR receiver when
the front panel of the Receiver is blocked.
WI-FI
BLUETOOTH
TRIG Z1
Z1 IR
Z2 IR (AVR21, AVR31, AV41)
RS232
This input is intended for use with an IR receiver in Zone 2 to
allow remote control of Receiver from a second room.
TRIG Z2
Z2 IR
AV
OUT
CAMBRIDGE, CB25 9PB, UK
DESIGNED IN THE UK
MADE IN VIETNAM
EN-14
A supplier of infra-red receivers and emitter accessories
and systems is Xantech. See www.xantech.com for more
WI-FI
BLUETOOTH
information, or ask your Arcam dealer.
tip: Modulated signal
NOTE: The IR inputs on the Receiver are designed
for modulated signals. If the external IR receiver
sleeve: Ground
demodulates the IR signal, it will not work. Also the
unit does not provide power for external receivers on
the IR jack, therefore an external power source will be
required.
and
) allow the connection of
NOTE: Sockets referring to 'Z2' relate to connections
used in multi-room installation. For more information
on these connectors, see page EN-11.
CAMBRIDGE, CB25 9PB, UK
DESIGNED IN THE UK
MADE IN VIETNAM
Publicidad
