Arcam AV41 Manual página 25

4. If you press the Device key together with the key one
more time within 30 seconds after LED blinks twice
** , you can finish the erase mode deleting all the
data learned on the Device. The LED blinks three times
*** to confirm.
To delete the learned data for a key for a device:
1. Press the Device key for the product you want to set up,
together with the key. Hold down both buttons for
three seconds until the LED stays lit.
2. Press and hold down the key on which you want to
delete the data for three seconds. The LED blinks twice
** . If any further key press is made, the remote
escapes from erase mode without deleting the learned
data.
3. If any further key press is not made for 30 seconds, the
**
LED blinks twice , the remote escapes from the
erase mode automatically without deleting the learned
data.
4. If you press the Device key together with the
again within 30 seconds after the LED blinks twice, all
the data learned for that Device is deleted and you leave
erase mode. The LED blinks three times *** in
confirmation.
Reading stored code numbers
1. Press the Device key for the product that you want to
set up together with the key. Hold down both keys for
three seconds until the LED blinks.
2. Press the key and count the number of blinks
( * =1, ** =2, *** =3, etc.). There is a time
gap between digits. (Note that '0' is represented by ten
blinks: ********** .)
Locking/Unlocking a specific
Device Mode
When you first unpack your remote and insert
the batteries, it is able to control certain Arcam
components automatically (e.g. BD players,
Amplifiers, Tuners and CD Players). We achieve this by
programming specific Arcam device codes onto the
relevant Device Mode keys, then locking the Device
Modes so you don't reprogram them inadvertently.
If you want to override these locked default settings
– to control a third-party BD player, for example – you
will first need to unlock BD Mode before setting up the
remote using one of the learning methods described
on the previous page.
Here are the factory default settings:
Device Default Default codes
Mode status
AMP Locked 001 (Arcam code 16)
key
BD
Locked 001 (Arcam)
AV Unlocked 108 (Philips TV)
UHD
Unlocked Code learning only
GAME
Unlocked Code learning only
STB Unlocked 030 (Bush/Goodmans/
Grundig, from SAT
database)
SAT Unlocked 128 (Sky+ Digital, from
SAT database)
PVR
Unlocked 018 (Humax PVR, from
SAT database)
CD
Locked 001 (Arcam)
Alternative codes are available for multi-room
solutions, or in the case of code clashes with other
manufacturer's products.
For example:
(system code 19): 002
Note that you need to change the system code
on the product you wish to control, as well as the
remote.
1. and are the Device keys that may be Locked
AMP, BD CD
or Unlocked.
Lock and Unlock are toggles (they change from Lock to
Unlock to Lock, etc.).
2. Press and hold the Device and keys together for three
seconds.
The power LED stays lit, showing that it is in Lock/Unlock
setup mode.
3. If there is no further key input for 30 seconds, the LED
goes off and the remote leaves Lock/Unlock setup mode.
4. To toggle the status of a device and then verify the status
of a device, press the keys in sequence:
If you have locked the device, the LED blinks three times:
***
.
If unlocked the device, the LED blinks five times:
*****
.
5. If you press a valid Device key within 30 seconds, the
***
LED blinks three times: and the remote leaves
Lock/Unlock setup mode.
Controlling the volume of other
devices
By default, the volume keys and mute key control
the amplifier volume.
You can configure these buttons so they send
volume commands to another device. In the
following example, the volume commands are sent
to a linked AV device (your television, for instance):
1. Press + for three seconds, until the LED lights and
stays on.
2. Press .
UP
again. The LED blinks three times *** .
3. Press
The volume and mute keys will now send the volume
commands to the TV.
To set the volume buttons to control the amplifier
once more, repeat the above steps, except press
in step 3.
EN-23
Hidden commands
Command Effect
'
AMP + Sends a Power On command
,
AMP + Sends a Power Off command
AMP + OK Sends a Zone command
>
Cycles through HDMI outputs 1, 2, 1&2.
AMP +
'
Sends a Power On command
CD +
,
CD + Sends a Power Off command
'
BD + Sends a Power On command
,
Sends a Power Off command
BD +
>
Sends a Resolution command
BD +
Factory default reset
You can reset your remote to the original factory
default settings.
Press and hold both the (home) and keys for
about five seconds until the power LED blinks five
times *****.
All programming and setup codes that you have
entered into the remote are erased and the remote
returns to the original factory default settings.
Device codes
The tables that are in the final section of this
Handbook list 3-figure codes for different
manufacturers' devices.
Use these when setting your remote up to control
your devices, as described in Direct code setup:
Method 1 (see previous page).
If more than one code number is listed, try the first
number. If the results are unsatisfactory, continue
trying the numbers for that manufacturer to get the
best 'fit' with the functionality required.
If the manufacturer of your equipment is not listed, you
can try Library search setup: Method 2 (see previous
page). This method allows you to scan through every
code contained in the remote's memory.
EN