Publicidad
Idiomas disponibles
Idiomas disponibles
Assemble water filter assembly
GB
• Open the cover of the water filter assembly. Take out the fil-
ter element and remove the plastic film. Put back the filter
element.
• Screw the filter connectors to both ends of the water filter
assembly
• Assemble filter assembly to filter holder by using 4 screws.
Tighten the filter by using wrench
Install the water inlet system
(Fig 4 on page 5)
A. Hose connector diameter 3/4"
B. Hose connector diameter 1/2"
C. Water filter assembly
D. Hose connector diameter 1/2"
E. Hose connector diameter 3/4"
F. Water inlet valve diameter 3/4"
G. Drain valve. The height of the sewage outlet must be lower
than the machine
I. Water filter inlet hose 1.5m long, part 11
II. Water filter inlet hose 0.7m long, part 12
• Connect A, B, C, D, E, F, I, II in sequence
• Connect Water drainage hose to drain valve. The height of the
sewage outlet must be situated lower than the appliance, so
that water can flow.
Note: The inlet water supply pressure range: 0.15 - 0.5 MPa.
Pressure reducer should be installed if the pressure over this
range.
Operating instructions
• Before first use, clean the appliance interior and exterior sur-
face with lukewarm water and a soft cloth.
• Position the appliance in a well-ventilated place, leaving at
least 150 mm gap around all sides for ventilation purposes.
• Let the appliance stand alone for about one hour in order to
settle the refrigerant. Make sure connect properly with the
water supply system.
• Then, plug in to a suitable socket.
• Press down the ON / OFF switch on the control panel in order
start up.
• Press and hold the cleaning button 2 seconds to start clean-
ing. This time, the "CLEAN" indicator will flash, water pump
turn on and clean for 30 minutes. After finish, the "CLEAN"
light will go off.
• Turn off the appliance and re-start the appliance again to
start to use.
• Also, the ON / OFF switch lights up in green. The appliance
starts to operate.
• The ice making process is completely automatic, it consists of
several stages as below:
Water inlet ==> ice production ==> ejection of ice ==> storage
of ice.
Then, push the slide door and use ice scoop to take out the ice.
• When the ice storage container is full, the "Storage tank is
full" indicator will light up in red and the appliance will stop
operation automatically.
• Once the ice have been removed, the appliance continue pro-
duction of ice automatically.
• Note: For sanitary reasons, you should dispose of the flake
ice produced in the first cycle for every use. Do not use them
12
for beverages or cooling food.
• If the water supply is insufficient, the "Water level is too low"
indicator will light up in red and the appliance will stop oper-
ate automatically. Check the water supply (hose) connected
to the appliance.
• If any error or failure occur, the "Display of fault" indicator
will light up in red and the appliance will stop operation au-
tomatically.
• Switch OFF the appliance by pressing down the ON / OFF
switch and unplug it from the electrical supply when not in
use.
Notes:
• DO NOT switch ON again the appliance immediately after
shut down automatically (caused by insufficient water supply,
flake ice container too full, current interruption). Wait at least
3 ~ 5 minutes in order to avoid damages to the compressor.
• Check the connectors of the water inlet and outlet hose regu-
larly for the leakage or overflow of water that may be present.
• If the appliance is not used for a long period of time, screw off
the drainage cover at the rear of the appliance. Wipe dry the
water tank using a dry, clean cloth.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
Cleaning
Automatic cleaning
• Fill some ice maker special cleaning fluid into the water box.
Power on and press the clean button for 3 seconds to start
the cleaning progress. The clean indicator light will flash in
the process. Automatic cleaning process will lasts 30 minutes
and it cannot be break unless you power off the machine. Af-
ter finished, drain the water box. Start the automatic cleaning
process again without cleaning fluid. If necessary, repeat it
one more time to rinse the residual cleaning fluid. Pull out
the drainage plug at the bottom of the water box, after water
drained away, install it back.
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent
and rinse with clean water.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for clean-
ing. Do not use petrol or solvents!
• No parts are dishwasher safe.
• Clean the condenser for every 2-3 months or when the inten-
Publicidad
