Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Product Familiarisation
1.
Auxiliary Handle
2.
Trigger Lock
3.
ON/OFF Trigger Switch
4.
Handle
5.
Battery Release
6.
Battery
7.
Battery Mount
8.
Battery Charge Indicator
9.
Motor Vents
10.
Pendulum Adjustment Lever
11.
Hex Key
12.
Base Plate Adjustment Screws
13.
Base Plate Guide
14.
Base Plate
15.
Blade Guide Roller
16.
Blade
17.
Cutting Guide
18.
Blade Holder
19.
Blade Holder Lever
20.
Blade Guard
21.
Parallel Guide
22.
Parallel Guide Adjustment Screws
23.
Parallel Guide Mounting Slots
24.
Battery Charger
25.
Charger Terminals
26.
Green LED
27.
Red LED
Intended Use
Single-speed pendulum action jigsaw for light duty cutting tasks of wood,
plastic and thin sheet metal (when using appropriate blades).
The tool must ONLY be used for its intended purpose. Any use other than
those mentioned in this manual will be considered a case of misuse. The
operator, and not the manufacturer, shall be liable for any damage or injury
resulting from such cases of misuse. The manufacturer shall not be liable for
any modifications made to the tool, nor for any damage resulting from such
modifications.
Unpacking Your Tool
•
Carefully unpack and inspect your product. Fully familiarise
yourself with all its features and functions
•
Ensure all parts of the product are present and in good
condition
•
If any parts are missing or damaged, have such parts
replaced before attempting to use this product
Before Use
Removing the Battery
•
To remove the Battery (6), press the Battery Release (5) and
slide the Battery out of the Battery Mount (7) (Fig. I (a-b))
Installing a charged Battery
1.
To fit a charged Battery (6), slide it into the Battery Mount
(7) (Fig. I (c))
Note: The Battery will fit only in one direction, which is determined
by its shape and the design of the Battery Mount. However, if the
Battery does not slide into the Battery Mount easily, do not force it.
Instead, pull the Battery out of the Battery Mount again, check for
correct position, and try again gently.
2.
Push the Battery into the Battery Mount until it locks into
place securely
Setting up the Charger
1.
If fitted, remove the Battery (6) from the Battery Charger
(24) (Fig. II (b))
2.
Connect the Battery Charger to the mains power supply
3.
The Green LED (26) on the Battery Charger will illuminate to
indicate that the Charger is powered.
WARNING: Only use this Battery Charger to charge the supplied
Battery or identical Silverline batteries.
WARNING: The Battery Charger is designed for indoor use only and
must not be exposed to moisture and rain.
Charging the Battery
WARNING: Failure to follow the correct procedure when charging the
Battery (6) will result in permanent damage.
Note: Normal charging time is 1 hour for a recently fully-discharged battery,
but if the Battery has been left in a discharged state for some time, it may
take extended time to charge.
1.
Slide a discharged or partially discharged Battery into the
Battery Charger (24) (Fig. II (a))
Note: Make sure the Battery and Battery Charger are lined up
correctly. If the Battery does not slide onto the Battery Charger
easily, don't force it. Instead, remove the Battery, then check that
the top of the Battery and the Battery Charger slot are clean and
undamaged and that the Charger Terminals (25) are not bent.
2.
Once charging commences, only the Red LED (27) will
illuminate
Note: If the Red LED is not constantly illuminated after an
uncharged Battery is inserted into the Charger, the Battery or
Charger may be faulty. Recheck the Battery is fully inserted in the
Battery Charger. If the fault persists do not use and contact your
authorised Silverline distributer.
3.
When the Battery is fully-charged only the Green LED (26)
will be illuminated
Battery Charge Level
The Battery has a built-in Battery Charge Indicator (8). Pressing on the
button to the right will indicate the charge level. The number of bars that
illuminate when the button is pressed indicate the charge level; 1 bar
indicating a low charge, 3 bars indicating a full charge.
IMPORTANT: When a low charge level is indicated, be aware the tool may
stop operating while in use. This may be dangerous. It is recommended to
always ensure the Battery has a good charge level.
Notes about battery charging
IMPORTANT: Batteries are an expendable supply whose capacity shortens
over time. Always adhere to the correct handling and charging instructions
in the manual. If the battery does not hold charge or working time is
shortened, purchase a genuine Silverline replacement.
•
The Battery (6) should be charged at ambient temperatures
between 10 and 40°C (ideally around 20°C)
•
After charging, allow 15 minutes for the battery to cool
before use
•
Ensure that the charger is disconnected from the mains
supply after use, and is stored correctly
•
Do not leave batteries on charge for extended periods and
never store batteries on charge
•
The Battery Charger (24) monitors battery temperature and
voltage while charging. Remove the Battery once charging
has been completed to maximise charge cycles of the
battery and not waste power
•
Batteries can become faulty over time, individual cells in
the battery can fail, and the battery could short. The
charger will not charge faulty batteries. Use another
silverlinetools.com
Original Instructions
10
Publicidad
