Publicidad
Idiomas disponibles
Idiomas disponibles
Read Operating Instructions
Please become familiar with all the instructions
and
warnings before operating any pneumatic
tool.
Always Wear Approved Eye Protection
Impact resistant eye proteclien should meet or exceed
the standards set forth in ANSI Z87t,
Occupational
and
Educational
Eye and Face Protection
Look for marking
Z87..t on your eye protection te ensure that it is an
approved style..
ttearing
Protection is Recommended
Hearing protection should be used when the noise level
exposure equals or exceeds an 8 hour time-weighted
average sound level of 85dBA
Process noise, reflective
surfaces, other tools being operated nearby, all add to the
noise level in a given work area. If you are unable to
determine your noise level exposure, we recommend the
use of hearing protection..
Avoid Prolonged Exposure to Vibration
Pneumatic tools can vibrate during use.. Prolonged
exposure to vibration er very repetitive hand and arm
movements can cause injury.. Discontinue the use of any
tool if you experience
tingling, numbness,
discomfort or
pain in your hands or arms. You should consult your
physician before resuming use of tool.
90 PSI Maximum
This tool is designed to operate at an air pressure of 90
pounds per square inch gauge pressure (90 PSI)
maximum, at the tool. Use of higher air pressure can, and
may cause injury. Also, the use of higher air pressure
places the internal components
under loads and
stresses they were not designed
for, causing premature
tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRYAND
PREFERABLY LUBRICATED.
FOR BEST RESULTS
DRAIN THE MOISTURE FROM YOUR COMPRESSOR
DALLY
Use Proper Accessories
Always disconnect tool from air supply before changing
accessories.
Never hold work in hands, lap or against
other paris of the body Secure all work with clamps or a
vice so that both hands are free to operate tool. Keep
proper footing and balance at all times.. Verify tool
direction before starting. Do not change direction of tool
while tool is running. Do not force tool, allow drill to work
at designed pace.
I, WARNINGI
Some dustcreated by power sanding, sawing, grinding,ddlltng
and other construction activities containschem}caIs knownto
cause cancer, birth defects or other reproductive harm Some
examples ofthese chemicalsare:
Lead fromlead based paint
crystalline silica from bricksand cement
and other masonry products, and
arsenic and chromium from chemically-
treated lumber.
Your risk from those exposures varies, depending on how often
you do thistype of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as dust masks that are
specilieally designed to filler out microscopic particles
(2)
FULL ONE YEAR WARRANTY ON
CRAFTSMAN AIR-DRIVETOOLS
If this Craftsman
tool fails to give complete satisfaction
within one year from the date of purchase, RETURN IT
TO THE NEAREST SEARS STORE IN THE UNITED
STATES, and Sears will repair or replace it free of charge
If this Craftsman
tool is used for commercial or rental
purposes, this warranty applies for only 90 days from the
date of purchase. This warranty gives you specific legal
rights, and you may also have other rights which vary
from state to state.
Distributed by Sears, Roebuck and Con, DepL 817WA,
Hoffman Estates, IL 60179,
The Craftsman
Model 875,. 199500 3!8" Reversible
Drill
is designed
for applications
which include
drilling,
honing, wire brushing
and fastening!unfastening
of
screws.. This tool features
a side mounted
reverse
lever for quick and easy direction
changes.
Features
•
Planetary gears for smooth power transfer and low
vibration.
Side mounled reverse lever for quick direction change..
•
Jacobs _ chuck for tong life
Specifications
Spindle Thread ...................................................................................................
3/8"x 24
Free speed (No Load) ........................................................................
2200 RPM
Weight .................................................................................................................................
2.1 lbs
Overall length .................................................................................................................
6-1/2."
Average air consumption ..................................................................
5 5 SCFM
Recommended hose size .....................................................................
318"[.D,
Air inlet..........................................................................................................................
I14" NPT
Maximum Air Pressure ............................................................................................
g0 PSI
Pre-Operation
Before thetoot isconnected t otheair supply, cfear theair
hose of accumulated
dust and moisture by running air
freely through the air hose for 5-10 seconds.
Before
removing a tool for service or changing sockets, make
sure the air line is shut-off at the compressor
This wilt
prevent the tool from operating if the throttle is accidently
engaged..
Installation
(See figure 1)
This tool is designed to operate at 90 psL Lower pres-
sure (below 90 psi) will reduce performance
of the tool
while higher air pressure (over 90 psi) raises the perfor-
mance of the tool beyond its rated capacity and could
cause serious damage to tool and user
Always use clean dry air Excessive moisture and dirt will
greatly reduce the life of any air motor. We recommend
the installation ef an in-line filter-regulator-lubricator
as
close to the tool as possible
A 3/8" air hose is required up to a length of 8 ft. If more
length is required a 112" air hose should be used at the
compressor. Attach a 3/8" whip hose for the remaining
4 - 8 ft.. for flexibility.. Be sure all hoses and fitlings are the
correct size and tightly secured before using air tool
Publicidad
