Seav TXS ESA NEW Guia De Inicio Rapido página 3

TSX ESA N R
EW ADIO CONTROL
6 channel transmitter with the capability for 12 and
18 bit code transmission and the division of codes
for common and
management.
TECHNICAL DATA
- Battery power supply:
- Working Frequency:
- Possible code combinations:
- Max. consumption:
- Working Temperature:
- Dimensions:
DESCRIPTION OF FUNCTIONS
The transmitter has six buttons for the separate
operation of 6 different users.
OPERATING INSTRUCTIONS
a) Standard configuration: T1-T3 12bit, T4-T6
18bit.
b) Configuration with T1-T6 18 bit.
c) Channel division: 1 common + 5 private.
d) Channel division: 2 common + 4 private.
e) Channel division: 3 common + 3 private.
a) Standard configuration T1-T3 12bit, T4-T6 18bit.
The transmitter is setup at the factory with the
following configuration: SW2 dip 1 and 2 off,
Jumper J1 open and buttons T1-T3 12 bit, T4-T6
18 bit. Maintaining compatibility between the TX
mono-bi-trichannel model and buttons T1 to T3
b) Configuration with T1-T6 18 bit.
To set-up the transmitter with
generating 18 bit code, connect the two poles of
the J1 jumper.
c) Channel division; 1 common + 5 private.
To set-up the transmitter to generate 1 common
code (e.g. for a condominium) and 5 private
users, set SW2 dip 1 to ON and dip 2 to OFF. As
personalised command
12VDC (23A)
433,92 MHz
262144
-2070°C
45x75x14mm
all buttons
the channel division is type 4+6 the first 4 dip of
GB
SW1 are for programming the common code and
the remaining 6 dip are for programming the
private code.
The set up of buttons T1 to T3 for 12 of 18 bit
transmission is controlled by Jumper J1, see
points a) and b) above.
d) Channel division; 2 common + 4 private.
To set-up the transmitter to generate 2 common
codes (e.g. for a condominium) and 4 private
users, set SW2 dip 1 to OFF and dip 2 to ON. As
the channel division is type 4+6 the first 4 dip of
25mA
SW1 are for programming the common code and
the remaining 6 dip are for programming the
private code.
The set up of buttons T1 to T3 for 12 of 18 bit
transmission is controlled by Jumper J1, see
points a) and b) above.
e) Channel division; 3 common + 3 private.
To set-up the transmitter to generate 3 common
codes (e.g. for a condominium) and 3 private
users, set SW2 dip 1 and 2 to ON. As the channel
division is type 4+6 the first 4 dip of SW1 are for
programming
remaining 6 dip are for programming the private
code
The set up of buttons T1 to T3 for 12 of 18 bit
transmission is controlled by Jumper J1, see
points a) and b) above.
Warning

The battery should be replaced every year to
guarantee
transmitter.

To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct
battery polarities.

Used batteries should be discarded in special
collection bins.

Use 12V 23A type batteries with maximum
operating temperature > 63 ° C.

Risk of fire or explosion if the battery is
replaced with an incorrect type.

Risk of explosion if the battery is disposed of
in a fire or hot oven, or if it is mechanically
crushed or cut.

Risk of an explosion or loss of flammable
liquids or gases if the battery is abandoned in
an environment with extremely high
temperatures.
the common code
the optimal range
Rev. 3.1
and the
of the
15/01/2024