Washer Care; Cleaning Your Washer; Water Inlet Hoses - Maytag MHN33PD Instrucciones De Instalación

WASHER CARE

Cleaning Your Washer

Cleaning the Door Seal/Bellow
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect the colored seal/bellow between the door opening
and the drum for stained areas. Pull back the seal/bellow
to inspect all areas under the seal/bellow and to check for
foreign objects.
A. Seal/Bellow
3. If stained areas are found, wipe down these areas of the seal/
bellow, using the procedure that follows.
a) Mix a dilute solution, using 177 mL (3/4 cup) of liquid
chlorine bleach, and 3.8 L (1 gal. ) of warm tap water.
b) Wipe the seal/bellow area with the dilute solution,
using a damp cloth.
c) Let stand five minutes.
d)
Wipe down area thoroughly with a dry cloth and let
the washer interior air dry with door open.
IMPORTANT:
Wear rubber gloves when cleaning for prolonged periods.
■
Refer to the bleach manufacturer's instructions for proper use.
■
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes
in combination with liquid chlorine bleach to thoroughly clean
the inside of the washer.
NOTES:
Read these instructions completely before beginning the
■
cleaning process.
If necessary, the cleaning cycle may be interrupted
■
by pressing the QUICK CYCLE key pad twice. However,
this will not immediately stop the cycle. The washer will
continue with several rinse and drain steps to ensure that
all remaining bleach is rinsed from the washer.
Begin procedure
1. Open the washer door and remove any clothing or items from
the washer.
2. Use liquid chlorine bleach:
Open the dispenser drawer and immediately add
160 mL (2/3 cup) of liquid chlorine bleach to the bleach
compartment.
NOTE: Do not add any detergent to this cycle. Use of more
than 160 mL (2/3 cup) of bleach will cause product damage
over time.
3. Close the washer door and the dispenser drawer.
A
4. To start the Clean Washer cycle, first enter "Start
Operating Setup." Then press and hold QUICK CYCLE
for one second. With the entire display flashing, press
STOP/PAUSE.
NOTE: The door will lock and the drum will rotate; then the
door will unlock, lock again, and then the cycle will continue.
The washer will not fill, but the drum will rotate while
■
the washer runs a short sensing cycle. This will take
approximately three minutes.
5. The cycle will determine whether clothing or other items are
in the washer.
a)
If no items are detected in the washer, it will proceed
to Step 7.
b)
If any items are detected in the washer, "rL" or "F-34"
will be displayed. Then the door will unlock.
Press QUICK CYCLE to cancel the failure code.
■
Then repeat steps 1, 3, and 4 to start the cycle again.
6. Once the cycle has begun, allow the cycle to complete.
7. After the cycle is complete, leave the door open slightly,
to allow for better ventilation and drying of washer interior.
Always do the following to maintain washer freshness:
Use only "HE" High Efficiency detergent.
■
Leave the door slightly open after each cycle to allow
■
for better ventilation and drying of washer interior.
Clean the washer monthly using the Washer Maintenance
■
Procedure, and 160 mL (2/3 cup) of liquid chlorine bleach.
If the procedure does not sufficiently improve the washer
■
freshness, please evaluate your installation and usage
conditions for other causes.
Cleaning the exterior
Use a soft, damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer by pressing the Release Lever.
Remove the drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments).
3. Wash the parts under running water.
NOTE: Do not wash components in the dishwasher.
4. Replace the inserts and return the dispenser to the drawer.

Water Inlet Hoses

Replace water inlet hoses after five years of use to reduce the
risk of hose failure. Periodically inspect and replace water inlet
hoses if bulges, kinks, cuts, wear, or leaks are found.
When replacing your water inlet hoses, mark the date
of replacement on the label with a permanent marker.
17