Perry Electric 1IOIAWF0102 Guía Rápida De Usuario página 4

INSTALLATION: system set
Once the Wi-Fi astronomical
switch is installed in an
electrical panel, inaccessibility
to the terminals without
s p e c i a l t o o l s m u s t b e
guaranteed.
ELECTRICAL CONNECTIONS
Description of terminals:
230V~ power supply
terminal 5 = N (Neutral)
terminal 10 = L (Line)
Note: potential-free relay changeover contacts.
relay (C1)
terminal N° 1 = NO (normally open contact)
terminal N° 2 = C (common)
terminal N° 3 = NC (normally closed contact)
The electrical connections
must only be implemented
after having disconnected the
230V~ power supply.
CONNECTION OF THE Wi-Fi DEVICE TO THE APP
Log in to the App with the personal credentials. If you do not have the credentials, register (see the APP manual)
Note: in case of problems with the Wi-Fi network, it will also be possible to associate the device to the APP using the AP mode
(see description in the APP manual)
Ÿ
Follow the procedure of the APP step-by-step and associate the Wi-Fi
Ÿ
Once the association of the Wi-Fi device has been con rmed, proceed with the programming as described in the APP manual.
RESET
IMPORTANT! It is recommended for the installer or expert user
to perform the RESET as this deletes any previous settings
and programs.
To reset the Wi-Fi astronomical
function by keeping the button on the front of the Wi-Fi
pressed for 5 seconds.
IMPORTANT: the astronomical
programming is deleted and the device is set back to the factory default
settings.
Note: it will also be possible to delete the programming and/or association of
the device from the APP (see APP instructions).
OPERATION WITH NO POWER
If the 230V~ power is disconnected (e.g. a blackout), the
the current date and time are kept updated by the reserve charge of over 72 hours.
The language, programs and all previously entered settings are saved in a permanent memory.
IMPORTANT: sunrise and sunset times are not updated if there is no internet connection.
If power is interrupted for more than 72 hours, the current date and time update cannot be guaranteed.
When power and the internet connection return, the current date and time will be automatically updated.
Wi-Fi
ROUTER
Programmable even without
an internet connection
using a shared Wi-Fi network
Wiring diagram
to connect the Wi-Fi device
1 2 3 4 5
C1
6 7 8 9 10
E.g.: lamp
N
230 Vac
L
switch to the factory settings, run the Reset
astronomical
switch loses the association with the APP
astronomical
IMPORTANT!
the FIRST CONNECTION
presence of a Wi-Fi network connected to the Internet.
INTERNET
CONTROLS AND SIGNALS
Button to manually control the
N Wi-Fi astronomical switch
- quick press:
command to switch the relay
status (ON / OFF)
- pressed for 5 s
L
( rst switch-on) command to
search for a Wi-Fi network to
connect to.
- pressed for 5 s
(device already connected to
the network) RESET command.
astronomical
switch
, all
RESET:
press and hold the button
at the front for 5 seconds
switch disables the relay;
must be carried out in the
The blue status LED of the Wi-Fi network
Device status
Waiting to connect
to the Wi-Fi network
Connected to the Wi-Fi
network
Problems with the Wi-Fi
network
Red relay status LED
indicates whether the relay is on or off.
When the relay is ON, the LED will be on;
when the relay is deactivated, the LED
will be off.
switch to the App: «Add device»
SIMPLIFIED EU DECLARATION OF
CONFORMITY
The manufacturer declares that the type of radio
equipment indicated below complies with
5
Directive 2014/53/EU (RED).
The full text of the EU declaration of conformity is
available at the address shown on the label:
Manufacturer, Fabricat, Fabrikant, Fabbricante, Fabricante:
PERRY ELECTRIC S.r.l.
Via MILANESE, 11 - 22070 VENIANO (Como)
ITALY - www.perry.it
Tel. +39-031-8944.1 Fax +39-031-931848
http://www.perry.it/it/dichiarazioni.aspx
Type, T ypen , Tipo:
1IOIAWF0102
EN
refer to the APP manual
to download the APP:
Perry Timer
LED signal
ashing fast
off
xed
Series, serie:
V001
4