Publicidad
Idiomas disponibles
Idiomas disponibles
PRIORITY
In a situation in which two operations coincide at the same time, the ASTRO UNO
will always perform the OFF operation.
DISPLAYING THE PREOGRAMMED OPERATIONS
Press OK to enter the MENU PROGRAM, press OK again and the careen
changes to ENTER PROGRAM and again pressing OK the PROGRAM PROG 01
is entered and all programs from 1 to 22 can be displayed using the ∆ and ∇ keys.
TIMING DIAGRAM
Pressing "C" twice in normal mode C1 is displayed on the screen, together with its
status and timing diagram for the operations programmed in this circuit.
RESET ZEROING
When all four keys are pressed at the same time for more than three seconds, the
current programming is deleted, the equipment version is shown and the
LANGUAGE menu is entered. The two factory set programmes remain in memory.
MODIFYING OR DELETING OPERATIONS
Press OK to enter the MENU ZONE and use the ∆ and ∇ keys to select MENU
PROGRAM, press OK again and the screen changes to PROGRAM
PROG 01, use the ∆ and ∇ keys to select the program to be modified or deleted
and confirm with OK, which will display the selected program on the screen,
together with PROG X ENTER confirm with OK it is to be modified than proceed
as in section Programming. If the operation is to be deleted, use the ∆ and ∇ keys
to select DELETE and confirm with OK.
MANUAL OPERATION
Channel 1 can be temporarily enabled or disabled from normal mode. Press ∆.
PERMANENT MANUAL OPERATION
Enter PERMANENT MENU. Confirm with OK and PERMANENT C1: YES appears
onscreen, ∆ and ∇ are used to select C1: SI or C1: NO.
In order to activate permanent mode select the YES option and confirm with OK.
In order to deactivate permanent mode select the NO option and confirm with OK.
In permanent mode, circuit C1 remains constantly in the current position until this
permanent mode is deactivated.
When permanent mode is activated, it is possible to change its state (from ON to
OFF or vice versa) with the manual operation key (
permanent mode.
No programmed operations are executed in permanent mode. The corresponding
symbol is displayed when the circuit is in permanent mode (
ADVANCED PROGRAMMING (SPECIAL FUNCTIONS) EXTRAS
TIMING CHANGE (SEASON) (PUTTING CLOCKS FORWARDS/BACKWARDS)
Press OK to enter the MENU and use the ∆ and ∇ keys to select the EXTRAS
option. Confirm with OK and EXTRAS SEASON will appear on the screen, press
OK again and the screen displays SEASON: AUTO and the ∆ and ∇ keys are
used to select one of the three options. AUTO, STOP and MANUAL and confirm
the selected option with OK.
(If there is one or more programmed operations coinciding with the time change
period, these will be duplicated or are not performed depending on the time
change).
AUTO (the time change is automatically carried out on the last Sundays in March
and October at 02:00 and 03:00 respectively.
This option does not permit changes. When this option is chosen MENU EXTRAS
is displayed.
MANUAL (allows day and time to be chosen for the time change).
When this option is chosen EST W S is displayed, together with the month and
change date from winter to summer, with the date corresponding to the month
flashing and the ∆ and ∇ keys are used to program the month in which the time
change is to occur. Confirm with OK and the day figure flashes and the day, hour
and minutes are selected in the same manner, confirming with OK. EST S W
(summer – winter)is displayed and the date and time are programmed in the same
fashion.
STOP (no time change is made).
If this option is selected and confirmed with OK, no time change is performed and
MENU EXTRAS is entered.
PROGRAMMING THE FESTIVE PERIOD
In this period, the unit only performs the operations programmed as FESTIVES,
see the PROGRAMMING section.
FIXED TIME OR ASTRONOMIC OPERATION The (
during the FESTIVE period.
This menu only appears on the screen if operations have been programmed in the
PROGRAMMING MENU as FESTIVE.
Only one FESTIVE period can be programmed. The MENU EXTRAS FESTIVE is
entered and the screen displays FESTIVE STOP, which enables the FESTIVE
program to be disabled.
If a holiday program is to be entered, press ∆ and ∇ and FESTIVE EDIT is
displayed, confirm with OK and the INITIAL is programmed in the following order:
month, day, hour and minutes.
Then the holiday period END is programmed is the same way and in the same
order.
HOLIDAYS PROGRAM
No operations are performed in this period and the (
The MENU EXTRAS HOLIDAYS is entered and the screen displays HOLIDAYS
NOT USE, which enables the holidays program to be disabled.
If a holidays program is to be entered, press ∆ and ∇ and HOLIDAYS EDIT is
displayed, confirm with OK and the INITIAL is programmed in the following order:
month, day, hour and minutes.
Then the vacations period END is programmed is the same way and in the same
order.
WARNING: If an operation is programmed on a FESTIVE, the HOLIDAYS
program cannot be used and is removed from the menu remaining as a
FESTIVE period.
COUNTER
Entering in MENU EXTRAS COUNTER will show COUNTER C1 onscreen,
together with the hours that the C1 channel has been activated (ON position).
C1) without deactivating
)
) symbol is displayed
) symbol is displayed.
The counter will only increase hours when the equipment is powered up.
In order to reset the counter with COUNTER C1 displayed, simply pressing OK
will display DELETE C1, select YES with the ∆ and ∇ keys and confirm with OK.
12H - 24H MODES
Enter the 12H – 24H MENU EXTRAS, press OK and select the desired time
display mode with the ∆ and ∇ keys. Confirm the selection with OK.
CONTRAST
Enter the MENU EXTRAS CONTRAST, press OK, which displays the CONTRAST
screen, together with a number between 0 and 9 (default 6) corresponding to
screen contrast. The ∆ and ∇ keys are used to select the desired level of contrast
and confirm with OK.
TECHNICAL SPECIFICATIONS
Power supply
Switching power:
Maximum recommended loads:
Incandescent lamps:
Fluorescent lamps
Low voltage halogen lamps
Halogens (230 V)
Low-consumption lamps
Downlights
Leds
Contact:
Own consumption:
Assigned pulse voltage
Type of action:
Memory spaces:
Types of operation
Operation precision:
Operation precision:
Ball test temperature:
Operation battery backup:
Operating temperature:
Protection type:
Protection class:
Contamination situation:
Logic support class and structure:
Sealable cover
DIMENSIONS
35
02/12.201
ORBIS TECNOLOGÍA ELÉCTRICA S.A.
Lérida, 61
Tel.: + 34 91 567 22 77
As indicated on unit
16 (10) A/250 Vac
3000 W
1200 VA
2000 VA
3000 W
600 VA
400 VA
600 VA
AgSnO
switched
2
6 VA (1 W approx)
2.5 kV
Type 1B, 1S, 1T and 1U.
22
ON OFF ASTRONOMIC
One second
≤ ± 1sec/ day at 23ºC
+100ºC.
Four years without power (lithium battery)
From -10ºC to +45ºC
IP 20 in accordance with EN 60529
II in accordance with EN 60335 correctly
installed
Normal
Software class A
65
60
A016.26.55240
E-28020 MADRID
Fax + 34 91 571 40 06
E-mail: info@orbis.es
http://www.orbis.es
Publicidad
