Installation And Connections - JB Systems MPL-1 Manual De Instrucciones

ENGLISH
6. FOLDER button: Press this button to show the different folders (named 01\ ~ 02\ ~ 03\ ~ ...). Use the
SKIP buttons (3) to choose a folder and press the PLAY/PAUSE button (2) to select it. When the folder
contains audio tracks, the names of the audio tracks will be shown. If the folder doesn't contain any
tracks, the display shows "No Song".
7. EQ button: (only on remote)
Radio operation:
 Press the EQ button shortly to toggle between mono and stereo mode.
Note: In the APL-15 only Mono playback is possible, we suggest using the tuner always in
mono mode to reduce noise.
 Press the EQ button for about 3seconds to start the full automatic search and store function: the
complete FM-range is scanned, all available radio stations are automatically stored to the (max)
30 presets. Note: all previously stored station presets will be overwritten with new stations.
Player operation: each time you press the EQ button, another equalizer preset is selected: normal,
rock, pop, classic, jazz, blue, hall, bass, soft, country, opera. Just select the one you like most.
8. INPUT button: Press this button to select one of the 3 available options:
 USB-memory: if a USB memory device is inserted, the player will start playing the stored tracks.
 SD-card: if an SD or SDHC-card is inserted, the player will start playing the stored tracks.
 FM-radio: radio starts playing, make sure the antenna is in the right position.
9. LCD display: This graphic blue LCD-display shows a lot of information. The information shown depends
on which input is selected.
10. USB-input: here you can connect all kinds of USB-memories (USB-sticks, USB-hard disks, ...). As soon
as the memory device is inserted, the display shows "Searching", next the first track will be played.
Some important notes:
 The USB-memory should be formatted in FAT16 or FAT32 (most USB-sticks and small hard
disks are OK, however bigger hard disks are formatted in NTFS)
 Using a hard disk with external power supply is preferred, the USB-output on the MPL-1 is not
always able to supply enough current to the external hard disk.
11. SD-card input: here you can connect MMC, SD and SDHC memory
cards, formatted in FAT16 / FAT32. Insert the memory card until you
hear a small click. As soon as the memory device is inserted, the
display shows "Searching", next the first track will be played.
12. IR-RECEIVER: accepts IR-signals from the MPL-1R remote control.
13. MOUNTING HOLES: used to fix the MPL-1 in the APL-15 amplifier
module (see next chapter)
14. MULTI CONNECTOR: used to connect audio, antenna and power
input of the MPL-1. See the picture for the pinning of the connector.

INSTALLATION AND CONNECTIONS

Apart from installing the MPL-1 inside the APL-15 amplifier module, you can use it also for all kinds of other
applications. You can easily connect the supplied connection cable to the back of the MPL-1, the other end
has connections for audio left & right, FM-antenna, power supply (8V
connector in the previous chapter for more information.
Installing the MPL-1 inside the APL-15
amplifier module is quite easy, you only need a
screwdriver:
A. Turn the APL-15 amplifier module off and
remove the power cable. Use a suitable
screwdriver to loosen the 4 screws that hold
the small cover plate on the APL-15 in
place.
B. Remove the metal cover plate and keep the
4 screws, you will still need these. Inside
you will see a cable with special connector:
tear the connector gently a few centimeters
out of the APL-15
C. Connect it firmly to the back of the MPL-1
audio player module.
JB SYSTEMS
®
OPERATION MANUAL
to 18V ). See the picture of the multi
dc dc
3/21
ENGLISH
D. Install the MPL-1 gently in the compartment and use the 4 screws (A) to fasten the audio player in the
APL15.
Done!
SPECIFICATIONS
Input voltage:
Input current :
USB voltage:
USB current:
Accepted audio files:
FM Radio freq range:
FM Radio tuning steps:
Audio output:
IR-Remote replacement battery:
Dimensions:
Weight:
You can download the latest version of this user manual on our website: www.beglec.com
MPL-1 JB SYSTEMS
DC 8 to 18V
200 to 1000mA
5V +/-0,2V
dc
500mA
WMA, MP3 (different sample rates)
87,5 to 108MHz
0,1MHz
750mV
CR2025 3V battery (included)
110(W) x 44(H) x 65(D) mm
80grams
Every information is subject to change without prior notice
4/21
®
OPERATION MANUAL
MPL-1