Operations; Basic Operations - Clarion M608 Manual De Instrucciones

5. OPERATIONS

Basic Operations

Note:
• Refer to the diagrams in "3. CONTROLS"
when reading this chapter.
CAUTION
Listening to the unit at or near maximum
volume level can be harmful to your
hearing.
Power On / Off
Note:
• Start the engine before using this unit.
• Be careful about using this unit for a long
time without running the engine. If you
drain the battery too far, you may not be
able to start the engine and this can reduce
the service life of the battery.
1. Start the engine. The power button / knob
illumination on the unit will light up.
Engine ON
position
/ SRC] button on the front
2. Press the [
panel or remote control to turn on the
power under standby mode. The unit goes
back to the last status after power on.
3. Press and hold the [ / SRC] button on the
front panel or the remote control to turn off
the power.
Mute
Press the [MUTE] button on the remote control
to mute the volume from the unit.
Note:
Doing the operation above again or adjusting
volume will release muting.
Volume Adjustment
STANDARD: Rotate the [VOLUME] knob
on the front panel or press the [ ] or [ ]
button on the remote control.
MULTI ZONE: In Volume adjustment mode,
press the [ ] or [ ] button to select ZONE
number, then rotate the [VOLUME] knob to
adjust.
TOWER: In linked mode, rotate [VOLUME]
knob on the front panel or press the [ ] or [ ]
button on the remote control. In non-linked
while in volume adjustment press the [ ] or
[ ] button to select Zone 1 or Tower, then
rotate the [VOLUME] knob to adjust.
The adjustable range of volume is 0 to 40.
CAUTION
While driving, keep the volume level at
which external sounds can still be heard.
Changing Sources
/ SRC] button to change the
Press the [
operation mode.
Changing the Display
Press and the [ENT] button on the front panel
or press the [DISP] button on the remote control
to switch the display information from clock, sta-
tion information (radio mode), or track informa-
tion (USB mode).
System Setup
Changing Adjustment Settings
1. Press and hold [MENU] button to switch to
system setup mode.
2. Press the [ ] or [ ] button to select
the "item name".
3. Rotate the [UP/DOWN] knob to select the
"desired setting value".
* For some options, you should press the
[ENT] button to adjust the setting value.
4. After completing the setting adjustment,
press the [MENU] button to return to the
previous mode.
CLOCK
1. Press the [ENT] button.
2. Press the [ ] or [ ] button to select
the hour or the minute.
3. Rotate the [UP/DOWN] knob to set the
correct time.
* The clock is displayed in 12-hour format
by default.
4. Press the [ENT] button to store the time
into memory.
Note:
• T he clock can only be set while the unit
is on. If you drain or remove the boat's
battery or take out this unit, the clock will
reset. While setting the clock, if another
button or operation is selected, the clock
set mode is canceled.
AUDIO MODE
1. Rotate the [UP/DOWN] knob to select
STANDARD, MULTI ZONE or TOWER.
2. Press the [ENT] button to confirm.
DX/LO (RADIO mode)
Rotate the [UP/DOWN] knob to choose radio
local or distant at RADIO mode.
• LO: Only stations with strong signal can
be received.
• DX: Stations with strong and weak signals
can be received.
AUX SENS (AUX mode)
Rotate the [UP/DOWN] knob to choose AUX
Input sensitivity LOW, MID or HIGH in AUX
mode.
PARENTAL (SiriusXM mode)
Change parental password. Default code is
"0000".
LOCK CH (SiriusXM mode)
Lock the current channel
UNLOCK ALL CH (SiriusXM mode)
Unlock all parental locked channels.
SELECT
The "SELECT" menu is intended to auto-
matically pair with a stored mobile device.
This unit can store a maximum of three
mobile devices. The mobile devices will be
stored in the order they are paired to the
unit. If you wish to add a different device
than those already paired, you will need to
delete the unwanted mobile device from the
"DELETE" menu.
DELETE
1. Press the [ENT] button.
2. Rotate the [UP/DOWN] knob to choose
the paired mobile phone name from the
pairing list.
3. Press the [ENT] button.to confirm.
DISCON (BT mode)
Disconnect currently connected mobile
phone.
1. Press the [ENT] button, mobile phone
displays are currently connected.
2. Press the [ENT] button to disconnect.
AUTO CON: ON/OFF
1. Rotate the [UP/DOWN] knob to choose
AUTO CONNECTION ON or OFF.
ON: When detect the phone paired
before, the unit will reconnect to it auto-
matically.
M608
7