Publicidad
Idiomas disponibles
Idiomas disponibles
Verifying Receptacles for Correct Wiring:
Plug the transmitter into a standard 120 VAC receptacle. The three LEDs on the transmitter will indicate the wiring configuration
while the label on the transmitter interprets the LED lighting combinations.
Caution: The tester is for indication purposes only and a correct indication does not guarantee the integrity of the wiring. Any
incorrect or unclear indications should be referred to a licensed electrician for investigation and correction.
GFCI Testing (61-534)
1. Consult the GFCI device manufacturer's instructions to determine that the GFCI is installed in accordance with the manufac-
turer's specifications.
2. Check for correct wiring of the receptacle and all remotely connected receptacles on the branch circuit.
3. Operate the test button on the GFCI installed in the circuit. The test light will turn on, indicating the activation of the GFCI
test. The GFCI must trip. If the GFCI does not trip, consult a qualified electrician. If it does trip, reset the GFCI.
4. Activate the test button on the GFCI tester for a minimum of 6 seconds when testing the GFCI condition. Visible indication
on the GFCI tester must cease when tripped.
5. If the tester fails to trip the GFCI, it suggests: (a) a wiring problem with a totally operable GFCI, or (b) proper wiring with a
faulty GFCI. Consult with an electrician to check the condition of the wiring and the GFCI.
CAUTION: When testing GFCIs installed in 2-wire systems (no ground wire available), the tester may give a false indication
that the GFCI is not functioning properly. If this occurs, recheck the operation of the GFCI using the test and reset buttons. The
GFCI button test function will demonstrate proper operation.
NOTE:
• All appliances or equipment on the circuit being tested should be unplugged to help avoid erroneous readings.
• Not a comprehensive diagnostic instrument but a simple instrument to detect nearly all probable common improper wiring
conditions.
• Refer all indicated problems to a qualified electrician.
• Will not indicate quality of ground.
• Will not detect 2 hot wires in circuit.
• Will not detect a combination of defects.
• Will not indicate reversal of grounded and grounding conductors.
Clean with a dry cloth.
SPECIFICATIONS:
Operating Range: 100-120VAC
Operating Frequency: 47-63Hz
Maximum Load: 18A (4ms) at 120VAC, 200mW max, at 120VAC
Duty Cycle: Max: 4mS every 16.6mS (continuous), (.24%)
Weight (excluding battery): Transmitter approx 50gr., Receiver approx. 85 gr.
Power Supply: 9VDC battery
Operating Temperature: 0 to 50ºC
WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects or other
reproductive harm.
WARRANTY STATEMENT:
This tester is warranted to the original purchaser against defects in material and workmanship for two years from the date of
purchase. During this warranty period, IDEAL INDUSTRIES, INC. will, at its option, replace or repair the defective unit, subject
to verification of the defect or malfunction. Your original receipt from an authorized distributor of IDEAL INDUSTRIES, INC. is
your proof of purchase. Register your product at: http://www.idlim.net/support/registration/.
Any implied warranties arising out of the sale of an IDEAL product, including but not limited to implied warranties of
merchantability and fitness for a particular purpose, are limited to the above. The manufacturer shall not be liable for loss of
use of the instrument or other incidental or consequential damages, expenses, or economic loss, or for any claim or claims for
such damage, expenses or economic loss.
State laws vary, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
Warranty does not cover batteries.
Disposal of waste electrical and electronic equipment
In order to preserve, protect and improve the quality of environment, protect human health and utilize natural
resources prudently and rationally, the user should return unserviceable product to relevant facilities in accordance
with statutory regulations. The crossed-out wheeled bin indicates the product needs to be disposed of separately
and not as municipal waste.
Disposal of used batteries/accumulators!
The user is legally obliged to return used batteries and accumulators. Disposing of used batteries in the household
waste is prohibited! Batteries/accumulators containing hazardous substances are marked with the crossed-out
wheeled bin. The symbol indicates that the product is forbidden to be disposed of via the domestic refuse. The
chemical symbols for the respective hazardous substances are Cd = Cadmium, Hg = Mercury, Pb = Lead. You can return used
batteries/accumulators free of charge to any collecting point of your local authority, our stores, or where batteries/accumulators
are sold. Consequently you comply with your legal obligations and contribute to environmental protection.
IDEAL INDUSTRIES, INC.
Sycamore, IL 60178, U.S.A.
800-435-0705
www.idealind.com
ND 5416-7
Made in China
Publicidad
