Power Steel 15159 Manual De Instrucciones página 3

WARNING
READ AND FOLLOW ALL INSTRUCTIONS
WARNING-
TO REDUCE THE RISK OF INJURY, do not permit children to use this
product unless they are closely supervised at all times.
CAUTION-
This product is for use with storable pools only. Do not use with
permanently-installed pools. A storable pool is constructed so that it is capable of
being readily disassembled for storage and reassembled to its original integrity. A
permanently-installed pool is constructed in or on the ground or in a building such
that it cannot be readily disassembled for storage.
CAUTION-
Do not touch the panel surface when the product is working or you
may get hurt.
NOTE:
Do not sit, stand or jump on this product.
NOTE:
Weather conditions can affect the performance and life span of your solar
water heater.
NOTE:
This product must be set up on a flat and clean location; the ground must
be cleared of all objects and debris including stones and twigs.
NOTE:
Grass or other vegetation under the product will die and may cause odors
and slime to develop, therefore we recommend removing all grass from the
selected location. Avoid locating the item over of beside areas prone to aggressive
plant and weed species as they may damage the item when they grow.
NOTE:
This product must be placed in direct sun light to ensure proper
performance.
NOTE:
Drawings for illustration purpose only. May not reflect actual product. Not
to scale.
SPECIFICATIONS
Surface(m ) 3.41
Length(m) 2.84
Width(m) 1.2
Max Pressure(Psi 10
Material PVC
Channel System S-channel
Installation On Lawn/On Flat
50-100% of the swimming pool surface (increase
Characteristic swimming pool water temperatures by approximately
3-5°C 5-9°F
Ref.No. Description
1 Heat Panel
2 O-Ring(Φ24mm)
3 Hose Adapter
4 Adapter Nut
5 Hose Clamps
6 Hose(Φ32x1000mm)
7 Adapter Cap
8 O-Ring(Φ56mm)
To order spare parts for the Pool Solar Water Heater, please provide
us with part no. and part name.
Depending on the weather condition
QTY Spare Part No.
1
2 P6005
2 P6618
2 P6615
2 P6124
1 P6176
2 P6540
4 P6029
ASSEMBLY INSTRUCTIONS
1. Unplug the sand filter. Loosen the hose clamps on the pool's inlet and outlet
valves, replace the debris screens with stopper plugs (or close the connection
valves) to stop water to flow.
2. Follow the below diagram instruction to assemble all the parts properly;
NOTE:
Refer to the sand filter's owner's manual for assembly.
3. Loosen the hose clamps on the pool's inlet and outlet valves; replace the stopper
plugs with debris screens (or open the connection valves of the pool) to allow
water to flow.
4. Tighten the hose clamps, ensure no water is leaking and every connection is
securely fastened.
1
2
3
B
B
MAINTENANCE
CAUTION: YOU MUST ENSURE SAND FILTER IS UNPLUGGED BEFORE ANY
MAINTENANCE BEGINS OR SEVERE RISK OF INJURY OR DEATH EXISTS.
1) Unplug the sand filter.
2) Loosen all the hose clamps.
3) Remove debris screens from inside of pool. Replace the debris screens with the
stopper plugs in the pool's inlet and outlet valves. (Or close the connection valves A.)
4) Clean the panels with a garden hose carefully.
STORAGE
1) Unplug the filter pump or sand filter.
2) Follow the instructions as previously outline to stop water flowing to the filter
pump or sand filter.
3) Detach all hoses.
4) Dry all components thoroughly.
5) Roll all the panels.
6) Store the product in a dry warm location out of child's reach.
3
B B
B B
6
B
B
P-S-005174