Tabla de contenido
Publicidad
Function Buttons
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the How to Use The Basic/Advance Functions section of
this manual.
NOTE：Please do not select HEAT mode if the machine you purchased is cooling only
type. Heat mode is not supported by the cooling only appliance.
ON/OFF
Turns the unit on or off
MODE
Scrolls through operation
modes as follows:
AUTO g
COOL g
DRY g
HEAT g
FAN
ECO
Starts and stops energy
efficient feature. If hold
down this button for
more than 2 seconds,
MODE
the sleep feature is
activated.
TIMER
TIMER
Sets timer to turn unit on
and off(see How to Use
Basic Functions for
LED
instructions)
TURBO
LED
,
Turns indoor unit s LED
display on and off.
FOLLOW ME
Temperature sensing and
room temperature display
button.
TURBO
Enables unit to reach
preset temperature in
shortest possible time
Slide down the
front cover
Model: RG66B7(B)/BGEF
FAN
Selects fan speeds in
the following order:
AUTO g
LOW g
MED g
HIGH
NOTE: Holding this button
down for 2 seconds will
activate Silence feature.
TEMP
Increases temperate in
O
1 C increments.
Max. temperature is
ON/OFF
FAN
O
30 C .
TEMP
Decreases temperate in
O
1 C increments.
SWING
Min. temperature is
O
17 C .
SWING
FOLLOW
ME
SWING
SELF
Starts and stops horizontal
SHORT
CLEAN
CUT
louver movement
SWING
Starts and stops vertical
louver movement
SELF CLEAN
Starts and stops
self clean feature.
SHOUT CUT
Sets and activates your
favourite pre-settings.
3
Handling The Remote Controller
NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions
and How to Use Advanced Functions
sections of this manual for a detailed
description of how to use your air conditioner.
SPECIAL NOTE
Button designs on your unit may differ
slightly from the example shown.
If the indoor unit does not have a particular
,
function, pressing that function s button on
the remote control will have no effect.
INSERTING AND REPLACING BATTERIES
Your air conditioning unit comes with two
AAA batteries. Put the batteries in the
remote control before use:
1. Remove the back cover from the remote
control, exposing the battery compartment.
2. Insert the batteries, paying attention to
match up the (+) and (-) ends of the
batteries with the symbols inside the
battery compartment.
3. Install the back cover on.
INSTALLING REMOTE CONTROL HOLDER
The remote controller can be attached to a wall
or stand by using a remote controller holder
(optional part, not supplied with the unit).
1.
Before installing the remote controller, check
that the air conditioner receives the signals
properly.
2. Install the holder with two screws.
3. Put
the remote controller in the holder.
BATTERY NOTES
For optimum product performance:
Do not mix old and new batteries, or
batteries of different types.
Do not leave batteries in the remote control
,
if you don t plan on using the device for
more than 2 months.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for
proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL
The remote control must be used within 8
meters of the unit.
The unit will beep when remote signal is
received.
Curtains, other materials and direct
sunlight can interfere with the infrared
signal receiver.
Remove batteries if the remote control
w
ill
not be used more than 2 months.
Prevent any liquid from falling into the
remote controller. Do not expose the
remote controller to direct sunlight or
heat.
Remove the back cover
to install batteries
Put the remote controller
in the holder.
4
Publicidad
Tabla de contenido
