Tabla de contenido
Publicidad
PART NAMES AND FUNCTIONS
15. PITCH SLIDER
This slider is used to adjust the playback pitch
percentage. The slider is a set adjustment and will remain set until the
pitch slider is move or the pitch function has been turned off.
The TIME button will switch the time value
16. TIME BUTTON
described in the time meter between elapsed play time, track
remaining time, and total remaining time.
17. SGL/CTN BUTTON
between single track play or continuous track play (all tracks in order).
18. PITCH -/+ BUTTONS
increase when button is pressing and returns to the original pitch when
the button is released.
REAR PANEL
23. AUDIO OUT-SOCKETS
analogue. Connect the output to the respective input of your mixer.
24. DIGITAL OUT-SOCKET
digital. Connect the output to the respective input of a digital
amplifier for example.
25. RELAY SOCKET
Via the RELAY SOCKET, two CD players
DISPLAY
1. AUTO CUE:
This will indicate if the Auto Cue is on or off. Press
and hold the SGL/CTN for 1 sec. to turn the Auto Cue function on and
off.
Shows when the unit is set to play just one track at a
2. SINGLE:
time. When this is not lit the CD will play continuously through all
tracks. The function is controlled by the SGL/CTN button.
shows when the CD is repeating a particular area with the
3. LOOP :
music on the CD.
4. RELOOP:
shows when the CD has had a loop set previously and
4
This function allows you to choose
The desired pitch of CD decrease or
The music-signal of these sockets if
The music-signal of this socket is
19. JOG WHEEL
frame search during pause
This LED is illuminated when a CD tray is empty.
20. CD LED
21. FOLDER KNOB
choose the desired folder then turn the track knob to choose the
desired track within the folder; the folder and track name that is
playing showed in the LCD. ( Pushing the folder knob enter "folder
mode" to see the folder name when the normal mode.)
22. TRACK KNOB
turn this button to choose the desired track on the disc and show the
track name is playing in the LCD
can relay play.
If you connect with a mixer which supporting fader start, you can also
relay play via mixer's cross-fader
26. POWER SWITCH
27.AC CONNECTION
can go back to loop again.
5. ELAPSED, TOTAL REMAIN:
shown on the display is the ELAPSED, TOTAL REMAINING or
single song remaining time.
6. ~ 8.MINUTE, SECOND, FRAME:
information on the current track and time
9. TIME BAR:
on the setting of the TIME button.
10. PITCH:
indicator light to show percent of pitch is displayed.
11. PITCH:
Shows the pitch percentage of the song.
12. ANTI SHOCK AND BUFFER INDICATOR:
status is represented on the display by a bucket being filled or
emptied. The bucket itself represents the instant start function works
by buffer memory. If the bucket is flashing, the instant start is not
available. Each bar within the bucket represents 2 seconds of anti
shock protection. There is up to 10 seconds of anti shock available.
Lit when the unit is at a cue point.
13. CUE :
14. PAUSE:
The PAUSE indicators light during pause or cue mode.
15. PLAY:
lit while the unit is playing a CD.
16. CD INDICATOR:
drive.
17. MP3 INDICATOR :
in the drive.
18. CHARACTER DISPLAY:
track and album when a MP3 disc is loaded.
19. TEMPO LOCK:
active.
20. TRACK:
Shows the track that unit is playing with.
c d x - m p 2 0 0
The wheel is used for pitch bend while playing, or
Turning this knob enter "folder mode" to
Pushing the track knob into "normal mode" and
.
Press this button to start operation.
Plug the power supply cable in here.
These indicate that the time
These displays indicate
shows either time remaining or elapsed depending
This will indicate that a CD is loaded in the
This will indicate that a Mp3 disc is loaded
This will display the name of the
This will indicate the Tempo Lock function is
The memory
Publicidad
Tabla de contenido
