Setting The Transmission Channel - Monacor JTS TG-10STX/1 Manual De Instrucciones

Ocultar thumbs Ver también para JTS TG-10STX/1:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5 Operation
Always turn back all volume controls completely
before operating the transmitter.
1) Switch on the transmitter [press the button
POWER (2)] and switch on the receiver /
receivers TG-10R /1. The display (3) of the
transmitter shows the transmission channel
adjusted (b).
Set the transmitter and all receivers of the sys-
tem to the same transmission channel: Setting
the channel on the transmitter
setting the channel on the receiver
of the receiver.
2) Feed the audio signal to be transmitted to the
input. Adjust the level with the corresponding
volume control (5): control CH 1 for the signal at
the input CH 1 IN, control CH 2 for the signal at
the input CH 2 IN. If you use both inputs, use the
controls to mix the signals as desired. If you only
use one of the inputs, completely turn back the
control of the input not used.
The corresponding row of LEDs AUDIO
LEVEL (a) shows the level adjusted. There is an
optimum level control when the orange LED
lights up with signal peaks. In case of overload,
the red LED lights permanently. In this case,
turn back the corresponding control accordingly.
3) Each receiver TG-10R /1 features a control for
individual adjustment of the reproduction vol-
ume.
4) To switch off the transmitter after operation,
briefly keep the button POWER (2) pressed
until the display indications are extinguished.
Remember to switch off each receiver TG-10R /1
to save the battery.
If the transmitter is not in use for a longer
period of time, disconnect the power supply unit
of the transmitter from the mains socket. Even
when the transmitter is switched off, the power
supply unit has a low power consumption.
10

5.1 Setting the transmission channel

For wireless transmission, 16 channels
available (channel assignment
set the channel, use the buttons SET, + and - (4):
1) Keep the button SET pressed until the dot next
2) Select the channel with the button
3) Press the button SET to confirm. The dot next to
chapter 5.1,
manual
Note: Interference may be caused by other local wireless
transmitters. Therefore, when selecting the transmission
channel, set a channel on the receiver before switching on
the transmitter. If no interfering signals are received on this
channel, it is suitable for transmission.
5.2 Monitoring the signals via headphones
When headphones are connected to the jack
(6), it is possible to monitor either the transmission
signal or the signal of the audio source at the input
CH 3 (8) [
mono signal selected is fed to the left channel and
the right channel of the stereo headphones.
The headphones are operated via the knob "Moni-
tor Selector" (7) which is both a selector switch and
a volume control:
1) To select the monitor signal for the headphones,
2) To adjust the headphone volume, turn up the
to the channel indication (b) starts flashing.
(down).
the channel indication starts flashing rapidly
before it stops flashing.
chapter 4, step 4]. The corresponding
briefly press the knob. The corresponding LED
of the indication "Monitor" (c) lights up:
– If you select the transmission signal (mixed
signal CH 1/ CH 2), the LED "CH 1/ CH 2" lights
up.
– If you select the input signal of CH 3, the LED
"CH 3" lights up.
knob as desired.
CAUTION Never adjust a very high volume.
Permanent high volumes may
damage your hearing! Your ear
will get accustomed to high vol-
umes which do not seem to be
that high after some time. There-
fore, do not further increase a high
volume after getting used to it.
to
are
chapter 6.2). To
(up) or -

Publicidad

Tabla de contenido
loading

Tabla de contenido