Before Starting The Equipment - EINHELL TE-VE 550 A Manual De Instrucciones

Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Danger!
The electric power tool generates an electro-
magnetic fi eld during operation. Under certain
circumstances this fi eld may actively or passively
impede medical implants. To reduce the risk of
serious or fatal injuries, we recommend persons
with medical implants to consult their doctor and
the manufacturer of the medical implant prior to
using the equipment.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the vacuum extraction system and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand securely. All covers and safety devices
have to be properly fitted before the machine
is switched on.
Anl_TE_VE_550_A_SPK9.indb 21 Anl_TE_VE_550_A_SPK9.indb 21
GB
•
Before you actuate the On/Off switch, make
sure that the debris bags are securely faste-
ned!
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the machine to the power supply.
6. Assembly
(Fig. 1, 3-15)
Danger! Pull out the power plug before carrying
out any maintenance, resetting or assembly work
on the vacuum extraction system!
•
Undo the two nuts (E) on both sides of the
plastic housing (13) (Fig. 3).
•
Guide the side plates (12) over the screws on
the plastic housing (13) and secure them with
the nuts (E) (Fig. 4-5).
•
Place the strengthening plate (9) between the
side plates (12) and secure it with the screws
(B) and nuts (C) (Fig. 6).
•
Secure the chassis (8) to the side plates (12)
using the screws (D) and nuts (C) (Fig. 7).
•
Now thread the quick-release device (3)
through the sewn-in guide in the dust bag (2)
(Fig. 8-9).
•
Place the dust bag hook (1) into the hole for
the dust bag hook (14) on the plastic housing
(13) and attach the dust bag (2) to the dust
bag hook (1) (Fig. 10).
•
Snap the dust bag (2) over the top opening in
the plastic housing (13) so that it completely
surrounds the opening and secure it using the
quick-release device (3) (Fig. 11).
•
Pull the dust bag (6) over the bottom opening
in the plastic housing (13) so that it complete-
ly surrounds the opening and secure it using
the quick-release device (5) (Fig. 12).
•
Move a hose fastening (A) over the extractor
hose (11). Plug the extractor hose (11) onto
the extractor connection of the equipment
as far as the stop and secure the hose to the
connection using the hose clip (A) (Figure
13).
•
If equipment with an extractor connection
diameter of 100 mm is to be connected to
the extraction system, slip a hose fastener
(A) over the extractor hose (11). Now plug
the connection adapter (18) into the extractor
hose (11) as far as the stop and secure it by
tightening the hose fastener (A) (Fig. 14-15).
Plug the connection adapter (18) onto the ex-
- 21 -
17.06.2019 09:09:38 17.06.2019 09:09:38