Trimmer Safety Warnings - Makita 3710 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Bit protrusion
2 Base
3 Clamping nut
4 Scale
5 Adjusting screw
6 Wing bolt
7 Graduation
8 Wing nut
9 Trimmer shoe
10 Amount of chamfering
11 Switch lever
12 Loosen
SPECIFICATIONS
Model
Collet chuck capacity....................................6 mm or 1/4"
–1
No load speed (min ) .......................................... 30,000
Overall length ..................................................... 302 mm
Net weight ............................................................. 1.6 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

TRIMMER SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
6
Explanation of general view
13 Tighten
14 Hold
15 Spring washer
16 Flat washer
17 Bolt
18 Workpiece
19 Bit revolving direction
20 View from the top of
the tool
21 Feed direction
22 Straight guide
23 Screws
3.
3710
4.
5.
6.
/II
7.
8.
9.
10. Before using the tool on an actual workpiece, let
11. Be careful of the bit rotating direction and the
12. Do not leave the tool running. Operate the tool
13. Always switch off and wait for the bit to come to
14. Do not touch the bit immediately after operation;
GEA010-1
15. Do not smear the tool base carelessly with thin-
16. Draw attention to the need to use cutters of the
17. Some material contains chemicals which may be
GEB019-2
18. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
24 Screwdriver
25 Templet guide 10
26 Guide plate
27 Clamp screw (A)
28 Centre hole
29 Nail
30 Clamp screw (B)
31 Trimmer guide
32 Bit
33 Guide roller
34 Limit mark
35 Brush holder cap
Wear hearing protection during extended period
of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
correct shank diameter and which are suitable
for the speed of the tool.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
the material and application you are working
with.