Video Input; Aux Input - NAD C370 Manual Del Usuario

QUICK START
1. Connect the speakers to the Speaker A terminals and sources
to the relevant rear input sockets.
2. Plug in the AC power cord.
3. Press the POWER button to turn the NAD C370 on.
4. Press the required input selector.
NOTES ON INSTALLATION
Your NAD C370 should be placed on a firm, level surface. Avoid
placing the unit in direct sunlight or near sources of heat and
dampness. Allow adequate ventilation. Do not place the unit on a
soft surface like a carpet. Do not place unit in an enclosed
position, such a bookcase or cabinet, that may impede the air-flow
through the ventilation slots. Make sure the unit is switched off
before making any connections.
The RCA sockets on your NAD C370 are colour coded for
convenience. Red and white are Right and Left audio respectively,
and yellow for NAD Link. Use high quality leads and sockets for
optimum performance and reliability. Ensure that leads and
sockets are not damaged in any way and all sockets are firmly
pushed in.
For best performance, use quality speaker leads of 16 gauge
(1.5mm) thickness or more. If the unit is not going to be used for
some time, disconnect the plug from the AC socket.
Should water get into your NAD C370, shut off the power to the
unit and remove the plug from the AC socket. Have the unit
inspected by a qualified service technician before attempting to
use it again. Do not remove the cover, there are no user-
serviceable parts inside. Use a dry soft cloth to clean the unit.
If necessary, lightly dampen the cloth with soapy water. Do not use
solutions containing benzol or other volatile agents.
REAR PANEL CONNECTIONS (FIGURE 1)
GB
1. DISC INPUT
Input for additional line level input signals such as CD, Mini Disc
player or the output signal from a step-up amplifier for a
turntable. Use a twin RCA-to-RCA lead to connect the auxiliary
unit's left and right 'Audio Outputs' to this input.
2. CD INPUT
Input for a CD or other line-level signal source. Use a twin RCA-
to-RCA lead to connect the CD player's left and right 'Audio
Outputs' to this input. The NAD C370 only accepts analogue
signals from your CD player.

3. VIDEO INPUT

Input for the audio signal from a stereo VCR (or stereo
TV/Satellite/Cable receiver) or other line-level audio source.
Using twin RCA-to-RCA leads, connect to the left and right 'Audio
Out' of the unit to these inputs. Note: These are audio inputs only.

4. AUX INPUT

Input for additional line level input signals such as another CD
player. Use a twin RCA-to-RCA lead to connect the auxiliary unit's
left and right 'Audio Outputs' to this input.
4
NAD C370 Stereo Integrated Amplifier
5. TUNER INPUT
Input for a Tuner or other line-level signal source. Use a twin RCA-
to-RCA lead to connect the Tuner left and right 'Audio Outputs' to
this input.
6. TAPE 2 IN, OUT
Connections for analogue recording and playback to an audio
tape recorder of any type. Using twin RCA-to-RCA leads, connect
to the left and right 'Audio Output' of the tape machine to the TAPE
2 IN sockets for playback. Connect the left and right 'Audio Input'
of the tape machine to the TAPE 2 OUT sockets for recording.
7. TAPE 1 IN, OUT
Connections for analogue recording and playback to a secondary
audio tape recorder of any type. Using twin RCA-to-RCA leads,
connect to the left and right 'Audio Output' of the tape machine to
the TAPE 1 IN sockets for playback and tape monitoring. Connect
the left and right 'Audio Input' of the tape machine to the TAPE 1
OUT sockets for recording.
8. PRE OUT 1
In normal use the PRE OUT 1 is connected to the Main-In sockets
(No. 9) with the links supplied. The NAD C370 allows for the
connection of multiple power amplifiers. If you are using a single,
external stereo power amplifier, disconnect the links to the Main-
In sockets. The C370's internal power amplifier is now
disconnected. Use a twin RCA-to-RCA lead to connect to the left and
right 'Audio Input' of the Power amp to the PRE OUT 1 sockets.
If you are using an additional stereo power amplifier specifically
for Bi-Amping, use the PRE OUT 1 sockets to connect the power
amplifier with the lowest gain of the pair. Refer also to chapter "Bi-
Amping" for more information.
NOTES: Always turn the C370 and associated external power
amplifiers off before connecting or disconnecting anything to the
PRE-OUT 1, 2 and MAIN-IN sockets.
The PRE-OUT 1&2 output signals will be affected by the NAD
C370's volume and tone control settings.
9. MAIN IN
Connections to an external pre-amplifier or processor, such as a
surround-sound decoder. In normal use these are connected to
the Pre-Out 1 sockets (No. 8) with the links supplied. To connect
your NAD C370 to external processor or pre-amplifier first
remove these links. Use a twin RCA-to-RCA lead to connect to the
left and right 'Audio Output' of the pre-amp or processor to the
Main-In sockets.
NOTES: Always turn the C370 and associated external power
amplifiers off before connecting or disconnecting anything to the
PRE-OUT 1, 2 and MAIN-IN sockets.
The PRE-OUT 1&2 output signals will be affected by the NAD
C370's volume and tone control settings.
10. PRE OUT 2
The PRE OUT 2 sockets can be used to drive an additional power
amplifier. The VOLUME Pre-Out 2 control (No. 11) can be used to
reduce the output level of the pre-amplifier to the power amplifier
by up to -12dB. With the VOLUME Pre-Out 2 control set to the
maximum position (at the 0dB position), the output level will be
identical to that of the PRE OUT 1 sockets.