Before Starting The Equipment; Assembling The Components; Setting The Cutting Height; Operation - EINHELL RG-PM 48 S B&S Manual De Instrucciones Original

Anleitung_RG_PM_48_S_51_S_SPK7.qxd:_
GB
RG-PM 51 S B&S
Engine type:
Single cylinder four-stroke engine, 190 ccm
Working speed:
Fuel:
Cutting height adjustment:
Cutting width:
Weight:
Sound and vibration
L pA sound pressure level
K pA uncertainty
L WA sound power level
K WA uncertainty
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration emission value a h = 6.4 m/s
K uncertainty = 1.5 m/s 2

6. Before starting the equipment

6.1 Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can
A funnel (suitable for the tank's petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from
DIY stores)
An oil can with hand pump (available from DIY
stores)
Assembly
1. Affix the lower push bar (Fig. 3a/Item 5) to the
mower housing and set the desired working
height. 3 different working heights are available.
Each peg on the lower push bar can be inserted
into a hole situated directly opposite to it, on the
mower housing, for example A-A (Fig. 3). The
24
12.04.2012 10:43 Uhr
lower push bar must be equally adjusted on both
sides. Now affix the cover (Fig. 3a/Item 23) and
attach the push bar (5) using the square head
screws (15) and the star screws (18) as shown in
Figure 3a.
2800 min -1 /2,5 kW
2. Fasten the top push bar to the bottom push bar
standard petrol
using a screw (Fig. 3b/Item 16) and a star screw
central, (30-75 mm)
(Fig. 3b/Item 18) on each side. Make sure that
the lobes of the screws are folded towards the
510 mm
inside so that the high speed clamping function
39 kg
remains operational.
3. Insert the grip of the starter cord (Fig. 3c/Item 4)
into the hook provided for that purpose as shown
in Figure 3c.
4. Fasten the cords to the push bar with the
74 dB(A)
supplied cable ties (Fig. 3d/Item. 13).
5. The debris bag should be assembled as shown
4 dB
in Figure 3e. For this, insert the upper lugs of the
98 dB(A)
debris bag carefully into the openings on the
2 dB
lower debris bag.
6. Lift the ejector flap (Fig. 4 / Item 8) with one hand
and hook in the grass bag (Fig. 4/Item 7) as
shown in Figure 4
2

6.2 Setting the cutting height

Important! Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
imbalance, replace blunt and/or damaged blades
as a set only (if applicable). To carry out this
check, first switch off the engine and pull the
spark plug boot.
The cutting height is centrally adjusted with the
cutting height adjustor lever
(Fig. 7/Item 9). Up to 5 different cutting heights
can be selected.
Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position.

7. Operation

Note:
For detailed information on starting the engine,
refer to the enclosed manual from Briggs &
Stratton.
Important.
The engine does not come with oil in it.
Therefore, be sure to add oil before starting the
Seite 24