Bauhaus HGSI 45 Instrucciones De Manejo página 25

extension cable that is suitable for outdoor
use reduces the risk of electric shock.
3) Personal safety
a) Always pay attention to what you do and
apply reasonable care when working with
a power tool. Do not use the tool when
you are tired or under the influence of
medication, drugs or alcohol. When work-
ing with power tools even a short moment of
inattentiveness may result in severe injury.
b) Wear personal protection equipment and
always wear eye protection (safety gog-
gles). Wearing personal protection equip-
ment as a dust mask, nonslip safety shoes,
safety helmet or ear protectors (depending
on the type and use of the tool) reduces the
risk of injury.
c) Avoid unintentional activation. Ensure
that the electrical tool is switched off
before you connect it to the power supply
and/or the battery, pick it up, or carry it. If
you have your finger on the switch while car-
rying the electrical tool or connect the device
to the power supply with the switch activate,
then this may cause accidents.
d) Avoid unintentional operation. Make sure
that the switch is in 'OFF' position before
pulling the plug from the mains socket.
When carrying the tool with your finger on
the on/off switch or connecting the tool to the
mains supply with the switch in 'ON' position,
this may result in accidents.
e) Remove adjustment tools or wrenches
and the like before you switch the tool
on. A wrench or another tool that is inside or
on a turning part of the tool may cause injury.
f) Do not overestimate your abilities. Take
care of a safe footing and keep your bal-
ance at all times. This will allow you to bet-
ter control the tool in unexpected situations.
g) Wear suitable clothes. Do not wear wide
clo-thing or jewellery. Keep your hair,
clothes and gloves clear of all moving
parts. Loose clothing, jewellery or long hair
may get caught in moving parts.
h) If dust extraction/collection devices are
provided make sure that they are con-
nected and used properly. The use of
these devices reduces hazards caused by
dust.
GB | Operating Instruction
4) Careful handling and use of power tools
a) Do not overtax the power tool. Use the
b) Do not use a power tool with a dam-
c) Pull out the plug connector from the
d) Store power tools out of the reach of
e) Thoroughly maintain your power tool.
f) Keep cutting tools sharp and clean. Thor-
g) Use power tools, accessories, add-on
5) Appropriate handling and use of battery-
a) Make sure that the device has been
b) Only use charging devices recommended
GB-4
power tool intended for your type of work
in each case. The use of the suitable power
tool within the stated range of performance
makes working more effective and safer.
aged switch. A power tool that cannot be
switched on or off any more is dangerous
and must be repaired.
socket and/or remove the battery before
you change the device settings, change
accessories, or put away the device.
These care instructions prevent the device
from starting unintentionally.
children. Do not allow persons to use the
tool if they are not familiar with the tool
or these instructions. Power tools are dan-
gerous if used by inexperienced persons.
Check whether moving parts are working
properly and are not jamming/sticking,
and whether parts are broken or other-
wise damaged in a way that affects the
function of the tool. Have damaged parts
repaired before using the tool. Many ac-
cidents are the result of poorly maintained
power tools.
oughly looked-after cutting tools with sharp
cutting edges are jamming less often and
are easier to guide.
tools, etc. in accordance with these in-
structions and in the way prescribed for
the respective type of tool. You should
also consider the working conditions
and the work to be carried out. The use
of power tools for purposes other than those
intended for the respective tool may result in
dangerous situations.
operated power tools
switched off before inserting the battery.
Inserting a battery into a switched-on power
tool may lead to accidents!