Tone Control - RIDGID R84082 Manual Del Operador

OPERATION
STORING A PRESET IN MEMORY
See Figure 9, page 17.
The memory feature saves frequencies as presets in the
radio's memory. You can save up to ten frequencies in FM
mode (five in FM and five in FM2) and five frequencies in
AM modes.
To store a frequency in memory:
 Tune to the frequency you want to save.
 Press and hold any number until you hear 2 beeps.
The memory location will appear on the display under
PRESET.
NOTE: Choosing a memory location where a frequency is
already saved will change the preset to the new frequency.
To recall a preset frequency:
 Press the numbered button corresponding to the memory
location number of the saved frequency.
 To exit a preset channel and return to Manual Tuning,
press one of the arrow keys.
STEREO/MONO (FM MODE ONLY)
See Figure 10, page 17.
To switch between stereo and mono broadcast:
 Press the MODE button until the Tools (
highlighted, then press Enter (
 Press either arrow button until the Stereo menu is
highlighted, then press Enter (
 Press either arrow button to switch between Stereo and
Mono and press Enter (
STEREO will be displayed on the LCD screen when the radio
is in stereo mode and the selected FM station is broadcasting
in FM stereo.

TONE CONTROL

See Figure 10, page 17.
To adjust the bass and/or treble settings:
 Press the MODE button until the Tools (
highlighted, then press Enter (
 Press either arrow button until the desired tone (Bass or
Treble) is highlighted, then press Enter (
 Press the arrow buttons as desired to add or subtract
bass or treble, then press Enter (
selection.
SETTING THE CLOCK
See Figure 11, page 18.
The time appears on the LCD display when the radio is on. If
the time is flashing on the display, the clock needs to be set.
To set the clock:
 Press the MODE button until the Tools (
highlighted, then press Enter (
) menu is
).
).
) to store your selection.
) menu is
).
).
) to store your
) menu is
).
 Press either arrow button until the Clock (
highlighted, then press Enter (
 Use the arrow buttons to choose between the 12-hour
and 24-hour clock, then press Enter (
selection.
 Use the arrow buttons to set the correct hour, then press
Enter (
).
NOTE: Pressing and holding the arrow buttons will cause
the numbers to advance more quickly.
 Use the arrow buttons to set the correct minutes, then
press Enter (
USING THE REMOTE CONTROL
See Figure 12, page 18.
In most instances, the buttons on the remote control operate
the same as the buttons on the radio itself.
 The POWER button (
and off.
NOTE: If the radio is in sleep mode, the power button
on the remote control will not power the unit. To turn the
radio on, use the ON/OFF/VOLUME knob on the front
of the radio itself.
 The MODE button displays available modes, allowing
you to choose between them using the arrow keys on
the remote.
NOTE: The Tools (
remote control. To activate anything within the Tools
menu, you must use the MODE button on the radio.
 Use the volume button (
volume of the radio.
 Press and release the left arrow button to tune to a lower
frequency and press and release the right arrow button
to tune to a higher frequency. When using an iPod, this
button will also allow you to move to the previous or next
song in the playlist.
 The MUTE button mutes the audio.
 In iPod mode, the PLAY (
the iPod audio.
USING AN iPod/MP3 PLAYER OR CD PLAYER
(NOT INCLUDED) WITH THE JOB-SITE RADIO
See Figures 13 - 15, page 18.
For dockable iPod models (with 30-pin connector):
Made for iPod touch (2nd generation), iPod classic, iPod with
video, and iPod nano (2nd, 3rd, 4th, and 5th generation).
 Press the MODE button until the iPod menu is highlighted,
then press Enter (
 Open the drop-down compartment door by pulling up on
the latch handle.
 Press the tabs on the front of the iPod cradle to lower the
cradle.
11 - English
).
) to store your selection.
) allows you to turn the radio on
) menu is unavailable from the
) to raise and lower the
) button starts and pauses
).
) menu is
) to store your