Cillit Optronic Serie Instrucciones De Montaje página 14

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
Operation
Operation
Operation
Operation
Operation
GB GB
GB GB
GB
Safety instructions
Safety instructions
Safety instructions
Safety instructions
Safety instructions
The operator must make sure that the unit always
contains sufficient active substance to provide
constant protection for the domestic water sys-
tem.
Special instructions for active substances
Special instructions for active substances
Special instructions for active substances
Special instructions for active substances
Special instructions for active substances
1. Only original BWT Quantophos F and Cu2 ac-
tive substances should be used for metering.
2. Mixing different active substance types is not
permitted and could cause the unit to malfunc-
tion.
3. Metered additives may not be transferred from
one container to another.
4. Damaged additive containers must not be used.
5. The contents of opened additive containers must
be used within 6 months as specified in
DIN 19635.
6. Observe the use by date on active substance
containers.
Note:
Note:
The type of activ
The type of activ
Note: The type of activ
Note:
Note:
The type of activ
The type of active meter
selected based on your local water conditions.
selected based on your local water conditions.
selected based on your local water conditions.
selected based on your local water conditions.
selected based on your local water conditions.
Do not use another type of active substance.
Do not use another type of active substance.
Do not use another type of active substance.
Do not use another type of active substance.
Do not use another type of active substance.
Note:
Note:
Note: If the water quality changes, a different ac-
Note:
Note:
tive substance may be required. Consult a spe-
cialist if this is the case.
Replacing the container
Replacing the container
Replacing the container
Replacing the container
Replacing the container
When
appears in the display and the audio
signal is emitted, the active substance container
is empty and must be replaced.
Impulsor Optronic
Impulsor Optronic
Impulsor Optronic
Impulsor Optronic
Impulsor Optronic
1. Undo the childproof lock (11
cap (7 7 7 7 7 ).
2. Turn the active substance container gently to
the left and remove it from the bottom above
the suction pipe (8 8 8 8 8 ).
3. Remove the aluminium seal from the new 3kg
mineral substance container.
1 4
1 4
1 4
1 4
1 4
e meter
e meter
ing substance is
ing substance is
e meter
e metering substance is
ing substance is
ing substance is
® ® ® ® ®
module
module
module
module
module F3
F3
F3
F3
F3
11) and flip up the
11
11
11
4. Lift the active substance container from the
bottom above the suction pipe (8 8 8 8 8 ) and attach it
by turning it gently. The
and the audio signal is switched off.
5. Flip down the cap (7 7 7 7 7 ) and secure the childproof
lock (11
11) with screws to prevent the mineral
11
11
11
substance container from twisting.
Connect the water flow. The metering unit is now
ready to use.
Impulsor Optronic
Impulsor Optronic
® ® ® ® ®
module
module
Impulsor Optronic
Impulsor Optronic
Impulsor Optronic
module
module T10/E20
module
Note: Do not lift or transport the active substance
Note: Do not lift or transport the active substance
Note: Do not lift or transport the active substance
Note: Do not lift or transport the active substance
Note: Do not lift or transport the active substance
container or canister by the suction lance han-
container or canister by the suction lance han-
container or canister by the suction lance han-
container or canister by the suction lance han-
container or canister by the suction lance han-
dle.
dle.
dle.
dle.
dle.
Prepare a new substance box or canister and
open the closure (remove the aluminium seal if
applicable). Unscrew the suction lance (9 9 9 9 9 ) from
the container and pull it out. Next, rinse the suc-
tion lance with clear drinking water. Insert the suc-
tion lance into the new container and tighten it.
The
message goes out, and the audio signal is
switched off. The metering unit is now ready to
use.
If the
indicator still appears in the display and
the audio signal is still being emitted even after
the container has been replaced, unplug the trans-
former plug and plug it back in after waiting a few
seconds.
message goes out,
T10/E20
T10/E20
T10/E20
T10/E20

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Optronic f3Optronic t10Optronic t20Optronic t10 dn 25Optronic t20 dn 25Optronic f3 dn 20 ... Mostrar todo

Tabla de contenido