Burnishing Machine Safety Warnings - SPARKY HeavyDuty SMD 1236CES Plus Instrucciones De Uso

ures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for op-
erations different from those intended could
result in a hazardous situation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical re-
placement parts. This will ensure that the
safety of the power tool is maintained.
Burnishing machine
safety warnings
Safety warnings common for sanding
with sandpaper and fibre wheels, wire
brushing, polishing operations with felt
wheels, polishing sponges, lambswool
pads and felt wheels with flange:
a) This power tool is intended to function
as a burnishing machine. Read all safety
warnings, instructions, illustrations and
specifications provided with this power
tool. Failure to follow all instructions listed
below may result in electric shock, fire and/
or serious injury.
b) Operations such as cutting-off are not
recommended to be performed with this
power tool. Operations for which the power
tool was not designed may create a hazard
and cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended
Original instructions
by the tool manufacturer. Just because
the accessory can be attached to your pow-
er tool, it does not assure safe operation.
▪ Never mount circular blades or grinding
wheels for angle grinders.
▪ Use only accessories appropriate for
the processed material and the rotation
speed.
d) The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can
break and fly apart.
e) The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool. In-
correctly sized accessories cannot be ad-
equately guarded or controlled.
f) Threaded mounting of accessories must
match the grinder spindle thread. for
accessories mounted by flanges, the ar-
bour hole of the accessory must fit the
locating diameter of the flange. Accesso-
ries that do not match the mounting hard-
ware of the power tool will run out of bal-
ance, vibrate excessively and may cause
loss of control.
g) Do not use a damaged accessory. Be-
fore each use inspect the accessory
such as backing pad for cracks, tear
or excess wear, wire brush for loose or
cracked wires. If power tool or accessory
is dropped, inspect for damage or install
an undamaged accessory. After inspect-
ing and installing an accessory, posi-
tion yourself and bystanders away from
the plane of the rotating accessory and
run the power tool at maximum no-load
speed for one minute. Damaged acces-
sories will normally break apart during this
test time.
h) Wear personal protective equipment. De-
pending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of fil-
trating particles generated by your opera-
tion. Prolonged exposure to high intensity
noise may cause hearing loss.
i) Keep bystanders a safe distance away
from work area. Anyone entering the
5
EN