Ardo PI58SF Instrucciones De Uso página 24

the same time.
This function allows to establish the time (from 1 to 99 min-
utes) or automatic switch-off of the cooking zone selected.
Activation:
1- Select the cooking zone (E).
2- Set the cooking level (from 1 to 9) desired, by acting on the
SLIDER control (D1).
3- Press the Timer button (N), the display will show
, At this point, the hob indicator (O) with the timer function
active, starts to flash.
4- Set the unit time (N2) desired from 0 to 9 by acting on the
SLIDER control (D1) e.g.
5- After a few seconds the unit value (N2) and the tenths (N1)
will appear fixed on the display
- if you want to set a time exceeding 9 minutes e.g:
just run your finger over the SLIDER control (D1).
- if, on the contrary, no operation is performed, it stops
flashing after a few seconds and the Timer display (Q) will
show the cooking time previously set
6- At the end of the programmed time, the timer display (Q)
and the hob indicator (O) will start to flash followed by an
acoustic sound.
To deactivate the acoustic signal just press the timer button
N, otherwise it will deactivate automatically after 2 minutes.
To deactivate the timer function before the set time:
- Select the cooking zone (E) and press one of the two buttons
(N). When the zone indicator (R) on display (E) stops flashing,
the function is no longer active.
Note: to display the residual cooking time, just press the
cooking zone (E) of interest selection button.
Minute Minder (Countdown) (Fig.2 - (Q)):
Attention! This function can only be used if no cooking
zone (E) has the timer inserted.
- The Minute Minder allows to set an established countdown
that goes from 1 to 99 minutes.
On expiry of the time, the hob emits an acoustic signal without
changing the active functions.
- The function activates only if the cooking level is set at "0"
on all displays (R).
- Press the Timer button (N) and set the time with the same
procedure as the Timer function, with the unique exception
that the indicators (O) do not switch on.
Note: whenever the Timer is to be activated on at least one
zone, the Minute Minder deactivates automatically.
To activate the Timer instead of the Minute Minder, pro-
ceed as follows:
1- Use one of the buttons to select (E) the cooking zone where
the timer function is to be activated.
2- Set the cooking level by acting on the SLIDER control (D1).
3- Select the Timer button (N).
4- Select the button (E) again where the timer function is to
be activated.
5- Select the Timer button (N).
6- Set the cooking time by acting on the SLIDER control (D1).
Booster (Fig.2 - (S)):
Depending on the appliance model, it may be fitted with a
Booster system which can be used to speed up cooking times
through the application of a power level which is greater than
the nominal value, within a defined period of time. The cook-
ing zones which can be used in conjunction with this function
are indicated in P Fig.2C.
To activate the Booster, switch the interested cooking area on
at any power level and press key S (Fig.2). This allows to reach
higher temperatures in a short time disbursing the maximum
.
;
.
power possible. Once the function is activated a red LED and
a P will appear on the display for ten minutes. After this time
the cooking area will automatically return to power level 9.
Attention!
- If your appliance has two zone cooking (P) using the Booster
function, these can be activated simultaneously.
- When the Booster function is active and the lower or upper
vertical cooking zone is to be switched on or is already on
(F1 or F2 - Fig.2) for the duration period of the Booster and
if maximum level is set, the power will decrease slightly.
- The Booster may not activate if, the cooking zone (with the
letter P) has been previously activated with high temperature
levels.
- In order to use the Booster function, wait for the P on the
display R to stop flashing and the temperature inside the
,
cooking surface to decrease.
Heat up (Fig.2 - (L1)) (Rapid heating):
The Heat up function can be used to set the cooking zone
to its maximum temperature for a specified period of time,
after which the temperature will return to a lower value set
previously.
To activate the Heat up function, select one of the cooking
zones (E).
Set the cooking level at "9" by acting on the SLIDER control
(D1), press Heat up (L1)and the cooking zone will show the
letter "A". This means that the (Heat up) function is active.
Set the desired cooking level (between 1 and 8); the cook-
ing zone display will now show the letter "A" and the desired
cooking level (e.g. 6) alternately.
- If no cooking level variation is made, the indicator (D2)
switches off.
Note: it is possible ONLY to increase the previously-set
cooking level:
1- Select the cooking zone (E) where the Heat up function
is active.
2- Increase the desired temperature by running your finger
over the SLIDER control (D1).
When the Heat up function has finished running, the hob will
emit a sound signal or BEEP; the relevant cooking zone will
continue to operate and the cooking level set previously, e.g.6.
Maintenance (Fig.5):
Remove any residues of food and drops of grease from the
cooking surface using the special scraper supplied on request .
Clean the heated area as thoroughly as possible using SIDOL,
STAHLFIX or similar products and a cloth/paper, then rinse
with water and dry with a clean cloth.
Using the special scraper (optional) immediately remove
any fragments of aluminium and plastic material that have
unintentionally melted on the heated cooking area or residues
of sugar or food with a high sugar content. In this way, any
damage to the cooktop surface is prevented.
Under no circumstances use abrasive sponges or irritating
chemical detergents such as oven sprays or stain removers.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 24 -