Quick Start Guide - nedis PASH120BKA4 Guia De Inicio Rapido

a

Quick start guide

Paper Shredder
For more information see the extended manual
online: ned.is/pash120bka4
Intended use
The Nedis PASH120BKA4 is intended to cut up to 6 sheets of A4-size
paper into strips or fine particles at once.
This product is not intended to shred cardboard or thick paper
sheets.
This product is intended for indoor use only.
This product is not intended for use by persons (including children)
with a reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning the use of the product by a person
responsible for their safety.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Specifications
Product
Article number
Dimensions (l x w x h)
Weight
Power supply
Power input
Power consumption
Operating cycle
Cutting style
Entry width
Shred capacity
Main parts (image A)
1
Control slider
2
Paper entry
3
Shredder
Safety instructions
- WARNING
• Ensure you have fully read and understood the instructions in
this document before you install or use the product. Keep this
document for future reference.
• Only use the product as described in this document. Any other
use may cause (serious) injuries.
•
Do not use the product if a part is damaged or defective. Replace
a damaged or defective product immediately.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualified technician for
maintenance to reduce the risk of electric shock.
•
Ensure that there is sufficient light when installing and using the
product.
•
Position the product close to a power outlet, so the power cable
can be unplugged easily.
• Make sure the power cable is positioned in a way that prevents
tripping or falling.
•
Unplug the product from the power source and other equipment
if problems occur.
• Do not unplug the charger by pulling on the cable. Always grasp
the plug and pull.
PASH120BKA4
Paper Shredder
PASH120BKA4
325 x 170 x 322 mm
3260 g
220 - 240 VAC / 50/60 Hz
1.4 A
300 W
2 minutes on / 60 min off
Cross cut
220 mm
6 sheets of 80 g of paper size A4
4
Carrying handle
5
Container
6
Power cable
•
Connect to a grounded outlet only.
• Do not let the power cable touch hot surfaces.
•
Do not expose the product to direct sunlight, naked flames or
heat.
• Do not expose the product to water or moisture.
• Do not immerse the product in water or other liquids.
•
Do not use the product if the surface is cracked.
•
Place the product on a stable and flat surface.
• Do not overfill the container. Empty the container before using
the product again.
•
Be careful when handling the blades.
•
Keep away from the paper entry to avoid cutting injuries.
• Keep clothing, necklaces, bracelets, loose hair and any other
object that can get stuck away from the paper entry.
•
Do not insert explosive materials, metal objects, or any other
foreign objects that can lead to hazardous situations.
• Before cleaning and maintenance, switch off the product and
disconnect the power.
•
When the product is not in use, disconnect it and store in a safe,
dry place, out of reach from children.
• Keep the product out of reach from children, infirm persons or
animals.
•
Do not let pets or children play too close to the product.
• This product is not a toy. Never allow children or pets to play with
this product.
•
Children should be supervised to ensure that they do not play
with the product.
• Do not move the product during operation.
• Do not use a damaged or defective product, but return it for
repair or replacement.
Installing the product
1. Place the product on a stable and flat surface.
2. Connect the power cable A
Using the product
1. Slide the control slider A
Standby mode is activated.
2. Insert max. 6 A4-size sheets of paper vertically into the paper
2
entry A
at once.
The product detects the paper and starts shredding.
Do not hold on to the paper when it is being shredded.
-
After shredding, the product returns to the standby mode
automatically.
Reversing the product
When paper is jammed in the shredder A
shredder blades to remove the paper.
1
1. Slide A to REV.
The product starts to reverse the running.
1
A slides to OFF.
1
2. Slide A to AUTO.
3. Insert max. 6 A4-size sheets of paper vertically into A
Troubleshooting
The product is There is too much
switched on, but cut paper into the
container A
the paper cannot be
shredded. paper cannot fall
down and stays at
A
3
6
to a power outlet.
1
to AUTO.
3
, you can reverse the
1. Disconnect the
product.
5
. The 2. Remove A
from A
3. Empty A
2
.
above a dust bin.
2
at once.
3
5
.
5