JB Systems Light DSP-4D Manual De Instrucciones página 4

ENGLISH
2. DMX Input: receives incoming DMX signal
3. DMX Output: links the incoming DMX signal to another DMX fixture.
4. DISPLAY: Shows the software version shortly after switching on the unit. Further shows the information
related to the selected function or working mode. The left digit shows the channel number, the 3 other
digits show the channel status:
 In the ADDRess menu: channel + DMX address is shown, ranging from 001 to 512
 In the MODE menu: working mode is shown. ("DIM" = dimmer mode * "SW" = switch mode)
 In the ALONE menu and standard display: channel output status is shown.
 Channel in dimmer mode: dimmer percentage, ranging from 0% to 100%
 Channel in switch mode: "ON" = output 100% * "OFF" = output 0%
 Curve : shows the dimming curve that is used
5. MENU BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
 Browse the main menu: Press the MENU button together with the UP/DOWN buttons.
 Return to the main menu: Press the MENU button to return to the main menu. (escape function)
6. DOWN BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
 Browse the main menu: Press the MENU button together with the UP/DOWN buttons.
 In the ADDRess menu: Press the DOWN button to lower the DMX address of the selected
channel. (press the button for a longer time to increase the speed)
 In the MODE menu: Press the DOWN button to put the selected channel in switch or dimmer
mode.
 In the ALONE menu: Press the DOWN button to lower the dimmer value (0~100%) when the
selected channel is in dimmer mode. (press the button for a longer time to increase the speed).
When the selected channel is set to switch mode, you can turn the output on or off.
7. UP BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
 Browse the main menu: Press the MENU button together with the UP/DOWN buttons.
 In the ADDRess menu: Press the UP button to increase the DMX address of the selected channel.
(press the button for a longer time to increase the speed)
 In the MODE menu: Press the UP button to put the selected channel in dimmer or switch mode.
 In the ALONE menu: Press the UP button to increase the dimmer value (0~100%) when the
selected channel is in dimmer mode. (press the button for a longer time to increase the speed).
When the selected channel is set to switch mode, you can turn the output on or off.
8. ENTER BUTTON: Please refer to the menu structure to understand the different menus. These are the
different possibilities:
 In the main menu: Press the ENTER button to select the desired sub menu.
 In a sub menu: Press the ENTER button to browse through the 4 channels.
9. DMX PRESENT LED: this LED indicates if the unit receives a DMX-signal on the DMX-input(n°2):
 LED is on: no DMX-signal detected on the input.
 LED is blinking: DMX-signal detected on the input
10. CHANNEL OUTPUTS: Each channel output has its own output socket to connect any resistive and/or
inductive projector(s) or small light effects.
11. CHANNEL FUSES: Protects the individual channels. Replace a broken fuse always with a fuse with the
same rate.
12. INPUT FUSE: This is an automatic circuit breaker. When the fuse is blown, first locate and solve the
problem that caused the fuse to blow. When the problem is solved, simply push the button to reset the
circuit breaker.
13. POWER SWITCH: turns the unit ON / OFF.
14. POWER CORD: supplies main power to the fixture.
JB SYSTEMS
®
OPERATION MANUAL
3/35
ENGLISH
MENU STRUCTURE...
MAIN MENU:
This menu is used to select one of the 4 sub menus.
 Press the MENU button together with the UP/DOWN buttons to browse the menu.
 Press the ENTER button to select the desired submenu.
ADDRESS SUBMENU:
This menu is used to set the DMX address of the 4 output channels. Each channel can be set to a unique
DMX-address. You can even give 2 or more channels the same DMX address.
 Press the ENTER button to browse through the submenu.
 Once you selected the desired channel, press the UP/DOWN buttons to set the address
 Press the MENU button to return to the main menu.
MODE SUBMENU:
This menu is used to set the working mode of the 4 output channels.
 DIM mode: use this mode when you connect lamps (projectors) to this output channel. You will be able to
dim the output smoothly between 0% and 100%.
 SWITCH mode: use this mode when you connect small light effects to this output channel. You can toggle
the output between ON (100% output) and OFF (0% output). Now you can switch small light effects on/off
with your DMX-controller.
 Press the ENTER button to browse through the menu.
 Once you selected the desired channel, press the UP/DOWN buttons to set the working mode.
 Press the MENU button to return to the main menu.
ALONE SUBMENU:
This is the standalone mode; all output levels can be set directly on the control panel so you don't need a
controller. It's important to know that the output settings are preserved when the unit is disconnected from
the mains. This makes the DB-46 very useful to illuminate exhibition booths etc.
 Press the ENTER button to browse through the menu.
DSP-4 JB SYSTEMS 4/35
®
OPERATION MANUAL
DSP-4