JB Systems Light LEDCON-02 Manual De Instrucciones página 4

ENGLISH
FUNCTIONS (FRONT)
1. COLOR / CHASE BUTTONS: These buttons have different functions, depending on the selected
working mode (refer to n°2):
 FIXED COLOR MODE: You can select 9 different predefined colors.
 CHASE 2: You can select 8 different chases and a random chase. (sound activated or not)
 AUTO ADDRESS MODE: You can determine the order of succession of the connected LED PAR-
projectors. Refer to the chapter "ADDRESSING" for more information.
2. MODE SELECT BUTTONS: 3 buttons used to set the controller in different working modes:
 FIXED COLORS: select this mode if you want to use the "fixed color" buttons (1).
 CHASE MODE: used to select two different chase modes:
 CHASE 1: select this mode if you want to select one of the 12 color chases using the
"chase/color" fader (3). In Chase1 mode the yellow LED is lit.
 CHASE 2: select this mode if you want to use the controller as a 4 or 8 channel DJ light
modulator. You can use the "color / chase buttons" (see n°1) to select the different chases.
In Chase2 mode the yellow LED blinks.
 SPECTRUM MIX: select this mode if you want to select one of the 32 different colors using the
"chase/color" fader (3).
3. CHASE/COLOR FADER: used to select one of the available color chases:
 Left side of the fader indicates the different chases.
 Right side of the fader indicates the different colors.
Important remark: There's also a function called "color fade" which is very nice for "background
lighting" applications. Select this function to fade gently from one color to another. You can adjust
the fade-over time with the color-fade fader(4).
4. SPEED/FADE FADER: used to select the chase speed or color fade time:
 Left side of the fader indicates the chase speed, ranging from 2,5s to 0,1s.
 Right side of the fader indicates the color fade time, ranging from 12s to 2,5s.
5. MASTER FADER: used to control the overall dimming of the LEDs and overall strobe speed.
6. SOUND BUTTON: used to toggle the chase mode between sound and static mode. Press this button
during the "auto address" mode to select the previous projector. Refer to the chapter "ADDRESSING" for
more information.
7. FULL ON BUTTON: used to set the 3 colors (R+G+B) at maximum level. Press this button during the
"auto address" mode to select the next projector. Refer to the chapter "ADDRESSING" for more
information.
8. BLACKOUT BUTTON: used to set the 3 colors (R+G+B) at zero level. Press this button for about
5seconds to start the "automatic address" function. Refer to the chapter "ADDRESSING" for more
information.
JB SYSTEMS
®
OPERATION MANUAL
3/36 LEDCON-02
ENGLISH
FUNCTIONS (REAR)
9. POWER SWITCH: used to switch the unit ON/OFF
10. DC INPUT: connect the supplied AC/DC adapter to this input. If you should use another adapter, please
make sure that it has 9Vdc and minimum 300mA with + in the center.
11. DMX OUTPUT: Sends DMX-signals to the connected units.
12. CHASER CHANNEL MODE: used to determine if the LEDCON-02 should work as a 4 or 8 channel LED
light modulator. Please note that you should always run the "auto address" function after changing the
channel mode!
CONNECTIONS
With LED MANAGER and/or MINI LED MANAGER:
 Just "daisy chain" the DMX in/outputs of 1 or more LED-Managers with the DMX-output of the LEDCON-02
remote using a good quality balanced cable.
 The LEDCON-02 remote will be used to control all connected slaves. The LED Managers are automatically
switched as slaves (slave LED is lit). The controls on the slave units are disabled.
Important! Don't forget to run the "auto address" function; this will give all connected units their own
address. (Refer to the chapter "ADDRESSING")
With LED BALL, LED SPOT/WASH, or other LED projectors:
 Just "daisy chain" the DMX in/outputs of 1 or more LED BALL and/or LED SPOT/WASH projectors with the
DMX-output of the LEDCON-02 remote using a good quality balanced cable
Important! Don't forget to run the "auto address" function; this will give all connected units their own
address. (refer to the chapter "ADDRESSING")
JB SYSTEMS
®
OPERATION MANUAL
4/36 LEDCON-02