Descargar Imprimir esta página
DeWalt DXST4500DK Manual De Instrucciones

DeWalt DXST4500DK Manual De Instrucciones

Kit de cajones para estantería industrial

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113
(APR18)
Part No. 41559
Copyright © 2018 D
D
WALT
and the D
WALT Logo are trademarks of the D
®
E
E
and are used under license. The yellow/black color scheme is a trademark for D
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please
read the manual and pay attention to these symbols.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE:
Indicates a practice not related to personal injury which, if not avoided,
may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
CALL US TOLL FREE AT: 1-844-377-8451
WARNING! Read and understand all instructions.
manual contains important safety and operating instructions.
Please read this manual carefully before assembling this storage
rack and save it for reference.
SAVE THESE INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Technical Specifications
Height
Width
Depth
Drawer Capacity
GENERAL SAFETY
• Keep work area clean and dry.
• Use correct/recommended tools for the job.
• Never leave tools unattended.
• Never force a part into place.
• Wear safety apparel.
• Wear safety glasses/goggles.
• Never overload the Drawer Kit.
• Do not leave drawer open.
• Keep small parts away from children. Never leave small children unattended while assembling.
• Always use common sense – your personal safety is your responsibility.
SPECIFIC SAFETY FOR WALL MOUNT BRACKET
WARNING:
Serious injury or death can occur from the rack tipping over. To prevent this, the rack
must be secured to the wall, especially in earthquake-prone areas, or where surfaces are uneven, and
where children and/or pets are present. For added safety we recommend also mounting the rack to the
floor using D
WALT part number DXSTA04MP (sold separately).
E
DXST4500DK
Copyright © 2018, D
WALT
E
WALT.
E
WALT Industrial Tool Co., or an affiliate thereof
E
WALT power tools
E
& accessories.
WALT TOOL,
E
6.21" (15.77 cm)
42.95" (109.09 cm)
16.86" (42.82 cm)
120 lb (54.43 kg)
WARNING:
FOR THE DRAWER KIT AND RACK
• Maximum load for the Drawer: Up to 120 lbs. (54.43kg) when evenly distributed.
• Maximum load for each shelf: Up to 1,500 lbs. (680 kg) when weight is evenly distributed.
• It is recommended that the heaviest load be placed on the bottom shelf.
Parts List
No. Description
1
Fold Up Drawer
2
Drawer Pull
3
Mounting Bracket with Drawer Slides
4
Drawer Carriage Bolts
5
Drawer Carriage Nut
6
Locking Pin
7
10 mm Wrench
1
2
3
4
This
NOTE: DXST4500 Industrial Rack is sold separately.
BEFORE YOU BEGIN:
• Read all instructions thoroughly.
• Remove all components from the box, and lay them on the floor in an orderly fashion.
• Wear eye protection.
• Be cautious of sharp edges.
• Keep this information for further reference.
WARNING:
Serious injury or death can occur from the rack tipping over. To prevent this, the rack
must be secured to the wall, especially in earthquake-prone areas, or where surfaces are uneven, and
where children and/or pets are present. For added safety we recommend also mounting the rack to the
floor using D
WALT part number DXSTA04MP (sold separately).
E
Assembly / Installation (Fig. 1-4)
NOTE: This fold up drawer is designed to be placed under a shelf so that the shelf may act as the drawer top.
1. Open the fold up drawer and install the drawer pull by slipping it into the tabs on the inside of the fold
up drawer front. Secure it using the provided drawer carriage bolt and nut in the top corners of the fold
up drawer. Make sure the nuts are inside of the fold up drawer. (Fig. 1)
2. Using the remaining drawer carriage bolts and nuts, secure the top corners of the fold up drawer on the
opposite side of the drawer pull. (Fig. 2)
NEVER EXCEED THE FOLLOWING WEIGHT LIMITS
Qty.
1
1
2
4
4
4
1
5
6
7
READ ALL INSTRUCTIONS

Publicidad

loading

Resumen de contenidos para DeWalt DXST4500DK

  • Página 1 Drawer Carriage Bolts Drawer Carriage Nut Locking Pin 10 mm Wrench JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113 (APR18) Part No. 41559 DXST4500DK Copyright © 2018, D WALT Copyright © 2018 D WALT. WALT and the D WALT Logo are trademarks of the D WALT Industrial Tool Co., or an affiliate thereof...
  • Página 2 WALT WALT et le logo D WALT sont des marques de commerce de DEWALT Industrial Tool Co. ou d’une ® société affiliée à cette dernière et sont utilisés sous licence. L’agencement de couleurs jaune et noir est une marque de commerce des outlils électriques et accessorires D...
  • Página 3 1. Ouvrez le tiroir pliant et installez-le en le glissant dans les languettes internes situées sur la paroi avant (APR18) Part No. 41559 DXST4500DK Copyright © 2018, D WALT du tiroir. Fixez-le en plaçant les boulons et écrous de carrosserie fournis dans les coins supérieurs du tiroir pliant.
  • Página 4 SEGURIDAD ESPECÍFICOS PARA EL SOPORTE DE PARED Ensamblaje / Instalación (Fig. 1-4) NOTA: Este cajón plegable está diseñado para colocarse debajo de un estante, de modo que el estante ADVERTENCIA: Se pueden producir lesiones graves o la muerte si la estantería se vuelca sobre pueda actuar como la parte superior del cajón.