Before Starting The Equipment - Toolson PRO-HM 27 MAX Manual De Instrucciones Original

L sound pressure level ..................... 95.9 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 105 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Chiseling
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
Anl_PRO_HM_27_MAX_SPK7.indb 14 Anl_PRO_HM_27_MAX_SPK7.indb 14
= 18.083 m/s
2
h
2
- 14 -
GB
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Check the drilling point for concealed electrical
cables, gas and water pipes using a cable/pipe
detector.
5.1 Additional handle (Fig. 2)
For safety reasons you must only use the
demolition hammer with the additional
handle. The additional handle (4) enables you to
achieve better stability whilst using the demolition
hammer. The additional handle (4) can be turned
into any required position. Undo the screw (a) by
turning it in the "+" direction. Now turn the additio-
nal handle (4) into the most comfortable working
position for yourself and then tighten the screw (a)
again by turning it in the "-" direction.
5.2 Tool insertion (Fig. 3)
•
Clean the tool before insertion and apply a
thin coating of drill bit grease to the shaft of
the tool.
•
Pull back and hold the locking sleeve (2).
•
Insert the dust-free tool into the tool mounting
as far as it will go whilst turning it. The tool will
lock itself.
•
Check that it is properly secure by pulling the
tool.
5.3 Tool removal (Fig. 4)
Pull back and hold the locking sleeve (2) and re-
move the tool.
5.4 Chisel lock (Fig.5 Item 3)
When the chisel lock (3) is pressed, you can turn
the inserted chisel into the required position.
•
Press the chisel lock (3) towards the inserted
chisel.
•
While holding the chisel lock (3), turn the chi-
sel into the required position.
•
Let go of the chisel lock again.
30.04.15 15:20 30.04.15 15:20