Sears Craftsman 917.28903 Instrucciones De Operación página 19

BATTERY
Your tractor has a battery charging system
which is sufficient for normal use. However,
periodic charging of the battery with an au-
tomotive charger will extend its life.
, Keep battery and terminals clean,,
, Keep battery bolts tight.
• Keep small vent holes open,
, Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on
your tractor is maintenance free,, Do not
attempt to open or remove caps or covers.
Adding or checking level of electrolyte is
not necessary
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and termi-
nals can cause the battery to "leak" power,
I. Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor:,
2, Rinse the battery with plain water and
dry,,
3., Clean terminals and battery cable ends
with wire brush until bright,,
4. Coat terminals with grease or petroleum
jelly,,
5. Reinstall battery (See "REPLACING
BATTERY" in the SERVICE AND AD-
JUSTMENTS section of this manual).
TRANSAXLE COOLING
Keep transaxle free from build-up of dirt and
chaff which can restrict cooling,
Check V-belts for deterioration and wear after
100 hours of operation and replace if neces-
sary. The belts are not adjustable, Replace
belts if they begin to slip from wear_
ENGINE
LUBRICATION
Only use high quality detergent oil rated with
API service classification SG-SL. Select the
oil's SAE viscosity grade according to your
expected operating temperature.
[ SAtvtscosrrv GnAOr_.S
_-2,J..
o 3o ._-_ _u _
.
_,_
NOTE: Although multi-viscosity oils (5W30,
10W30 etco) improve starting in cold weather,
the oils wi!l result in increased oil consumption
when used above 32°F. Check yourengine
oil level more frequently to avoid possible
engine damage from running low on oil..
Change the oil after every 50 hours of opera-
tion or at least once a year if the tractor is
not used for 50 hours in one year. 1 9
Check the crankcase oil level before starting
the engine and after each eight (8) hours of
operation, Tighten oil fill captdipstick se-
curely each time you check the oil level,
TO CHANGE ENGINE OIL
Determine temperature range expected
before oil change° All oil must meet API
service classification SG-SL.
o
e
1,
2_
Be sure tractor is on level surface,,
Oil will drain more freely when warm,_
Catch oil in a suitable container,,
Remove oil fill capldipstick Be careful
not to allow dirt to enter the engine when
changing oil.,
Remove yellow cap from end of drain
valve and install the drain tube onto the
fitting.
Oil Drain "Valve
Closed and
Locked
Posil
Yellow
Cap
_Drain
Tube
3. Unlock drain valve by pushing inward
slightly and turning counterclockwise.
4. To open, pull out on the drain valve.
5. After oil has drained completely, close and
lock the drain valve by pushing inward
and turning clockwise until the pin is in
the locked position as shown.
6, Remove the drain tube and replace the
cap onto the end of the drain valve.
7. Refill engine with oil through oil fill dipstick
tube, Pour slowly Do not overfill_ For
approximate capacity see "PRODUCT
S PEClFtCATIONS"section ofthismanual
8 Use gauge on oil fill capfclipstick for
checking level, For accurate reading,
tighten dipstick cap securely onto the
tube before removing dipstick Keep oil
at "FULE' line on dipstick, Tighten cap
onto the tube securely when finished,
ENGINE OIL. FILTER
Replace the engine oil filter every season
or' every other' oil change if the tractor is
used more than 100 hours in one year_