Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Introduction
Congratulations on your purchase of the i2600 intelligent speaker
management system. Through the i2600 you will have the ability
to create complex speaker setups, complete with a whole host of
possible signal processors built onboard. These include delays,
equalizers, compressors, limiters, gates, expanders, automatic
gain control, and many other fantastic functions. The extensive
speaker routing system allows the i2600 to be used as a simple
mono 6-way system or stereo 3-way system. The i2600 was
designed for stereo operation, with two input channels accepting
stereo input sources. Despite this, the unit can easily function as
a dual mono system for two independent mono signals assignable
to any number of outputs.
We know how eager you are to get started – getting the unit out
and hooking all your gear up is probably your number one priority
right now – but before you do, we strongly urge you to take a
look through this manual. Inside, you will find important facts and
figures on the set up, use and applications of your brand new
speaker management system. If you do happen to be one of the
many people who flatly refuse to read user manuals, then we just
urge you to at least glance at the Getting Started section. After
glancing at or reading through the manual (we applaud you if
you do read the entire manual), please store it in a place that is
easy for you to find, because chances are there's something you
missed the first time around.
Getting Started
1.
Ensure the unit is unplugged and the power switch is turned off.
2.
Connect all required input and output devices to the Input A
and B and Output 1, 2, 3, 4, 5 and 6 connectors.
3.
Turn on any devices connected to the i2600's input connectors.
4.
Plug the i2600 into an appropriate power source and turn it on.
5.
Turn on any amplifiers or active speakers connected to the
i2600's outputs.
6.
The product's name will appear on screen and the unit will
initialize.
7.
Upon first use, the i2600 will begin with the default program.
8.
Push and hold any of the Input or Output buttons to enter
EDIT mode of the corresponding input/output.
9.
Momentarily pushing any if the Input and Output buttons will
immediately mute the corresponding input/output.
10. Use the NAV/PM1, PM2, and PM3 controls to scroll menus
and adjust parameters whenever in EDIT mode.
11. Pushing the ENTER button will confirm any new settings.
12. Pushing the ESC button at any time will return to the previ-
ous menu, cancelling any new settings.
i2600
Factory Reset
In the event of the password being lost or forgotten, or any other
reason, the user may require the unit to be reset to the original
factory settings. In this event a factory reset will clear any and all
settings of the i2600 and return the device to the original factory
settings.
Warning: Continuing with this process will mean the i2600 will re-
initialize to the original factory settings and any previously stored
information and changed parameters will be permanently lost.
Note: As this process will turn the i2600 back to the factory default
settings, your current password will be replaced by the factory
default password: "000000".
To restore your i2600 to factory settings:
1. While the i2600 is switched off, simultaneously press and hold
the ENTER, ESC and UTILITY buttons on the front panel.
2. Maintain pressure on all three buttons as you turn the power
switch on. The screen will read "Memory Reset" to indicate that
the factory reset is taking place.
3. Release the buttons and wait for the i2600 to re-initialize.
Once completed, the i2600 will resume regular operation as though
it were a new unit from the factory and no previously programmed
parameters will be available for use.
PC Software Installation
1. Install the i2600 PC software on the included CD by running
setup.exe.
2. Install the USB driver using the file on the included CD named
USBdriverForWinX(v20814)_Setup.exe.
3. Connect the i2600 to your computer through the USB
connection. Windows will find the necessary driver.
i2600
Computer
4. Find the COM port used by your i2600 by going into the Device
Manager window. To do this, right click "Computer" on your
desktop and select "Manage". The Device Manager can be
found within this menu. Here, the i2600 should be shown like th
is:
As you can see, the COM port used
is visible in the device name (COM4). The COM port can also
be changing by editing the Device's properties.
5. Open the i2600 software by double-clicking the desktop icon.
6. Select File > Preferences to ensure the COM port settings are
correct, then select File > Connect to Networks. When the
i2600 is successfully connected to the computer, the name of
the product will be displayed in red within the software
1
Publicidad
Capítulos
Tabla de contenido
