General Warnings - nuair RevolutionAir Kit Comby 8221 594 Manual De Instrucciones

GENERAL WARNINGS

Compressed air is a potentially dangerous form of energy. Therefore, always take great care when using the compressor or the accessory kit.
To use compressed air, you must know and comply with the regulations established case by case.
When using air-powered accessories, always wear safety clothes. Keep the work area free and always maintain a stable position. Do not
allow inexpert persons to use tools without suitable supervision. Keep children and animals at a distance from the work area; improper use
of compressed air may cause serious injuries.
COMPRESSOR - ACCESSORIES CONNECTION
Make sure that the compressor is OFF before connecting the accessories
1) Connect the coiled air line B to compressed air outlet C (fig. 1a) using coupling D. Push coupling D firmly inside outlet C. A clicking noise will
indicate that the coupling is engaged
2) Once you have fastened this end of the coiled air line B, you can connect any accessory to the other end E, pushing firmly, for example, coupling
F inside E (figures 3a - 4a). In this case also, a clicking noise will indicate that the coupling is engaged
NAIL / STAPLER GUN -
RECOMMENDED OPERATING PRESSURE: 6 BAR
For nailing/stapling wood, laths etc..
If not used correctly and without suitable maintenance, the
nail/stapler gun can cause serious injury or death.
Prior to maintenance, lubrication, loading of nails/staples or
removal of jammed nails/staples, always make sure that you
have unplugged the nail/stapler gun from the compressor.
Always wear goggles and ear plugs when using the nail/stapler
gun.
Never direct the nail/stapler gun towards persons or animals
or yourself.
Never use the nail/stapler gun against metal or masonry objects.
Handle the nail/stapler gun holding it firmly by the grip only.
Never exceed the working pressure indicated for this accessory.
2.1 - TIPS FOR USING THE NAIL / STAPLER GUN
1) Before using the nail/stapler gun for the first time and after each
use, lubricate air inlet E of the nail/stapler gun (fig. 2)
2) Check that protector A of the nail/stapler gun is working correctly.
Check by hand that is free to move to-and-from without any
obstruction (fig. 3)
Never load the nail/staple cartridge without first of all checking
that protector A is working correctly.
Never connect the nail/stapler gun to the compressor without
first of all checking correct functioning of protector A.
3) Release the outer part of cartridge C from the locked position,
pressing button D (fig. 4)
4) Slide the outer part of cartridge C downwards (fig. 5)
5) Insert a set of nails/staples H in the housing of the cartridge L (fig.
6a - 6b) checking correct positioning
6) Slide the outer part of cartridge C upwards (fig. 7)
7) Block the outer part of cartridge C pushing this in until complete
connection of button D. Make sure that the cartridge is securely
fastened (fig. 8)
8) Connect the nail/stapler gun to the compressor as explained in
chapter 1 «COMPRESSOR-ACCESSORY CONNECTION»
9) Adjust working pressure to the value indicated for this accessory
10) The nail/stapler gun is now ready for use. Before proceeding with
the actual work, it is advisable to practice on a test piece in order to
check penetration of the nails/staples: use a piece of reject wood of
a thickness exceeding the length of the nails/staples. Rest point A of
the nail/stapler gun against the surface of the wood and press trigger
B. If the nail/staple does not penetrate to the depth required, set the
air pressure to a higher value WITHOUT HOWEVER EXCEEDING
THE VALUE INDICATED IN THIS MANUAL (fig. 11)
2.2 - MAINTENANCE
Before each use, lubricate air inlet D of the nail/stapler gun (fig. 2).
If a nail/staple remains jammed inside the nail/stapler gun, comply
scrupulously with the procedure indicated:
1) Switch off the compressor
2) Disconnect the nail/stapler gun from the compressor
3) Release the outer part of cartridge C from the locked position,
pressing button D (fig. 4)
4) Slide the outer part of cartridge C downwards (fig. 5)
5) Using a suitable Allen wrench G remove screws M and N, located
in the upper part of the nail/stapler gun (fig. 9)
6) Remove the cover I of the nail/stapler gun (fig. 10)
7) Remove any jammed nail/staple
8) Replace the cover I of the nail/stapler gun
9) Using a suitable Allen wrench G on screws M and N, secure these
again to the cover I
10) Slide the outer part of cartridge C upwards (fig. 7)
11) Block the outer part of cartridge C pushing this in until complete
connection of button D. Make sure that the cartridge is securely
fastened (fig. 8)
12) Connect the nail/stapler gun to the compressor as explained in
chapter 1 «COMPRESSOR-ACCESSORY CONNECTION»
13) After restarting the compressor, the nail/stapler gun is ready for
use
After use, always store the nail/stapler gun in a dry, clean environment.
Do not use solvents, flammable or toxic liquids to clean the gun.
7
GB
1
2