Caliber HCG 009DAB Manual De Instrucciones página 3

MANUAL
Precautions
Points to observe for safe usage
Read this manual carefully before using this item and its components.
They contain instructions on how to use this product in a safe and
effective manner. Caliber Europe BV cannot be responsible for problems
resulting from failure to observe the instructions in this manual.
Turn off the device immediately in case of a problem.
Failure to do so may cause personal injury or damage to the product.
Return it to your authorized Caliber Europe BV dealer for repairing.
Product cleaning.
Use a soft dry cloth for periodic cleaning of the product. For more
severe stains, please dampen the cloth with water only. Anything else
has the chance of dissolving the paint or damaging the plastic.
Temperature.
Ensure that the ambient temperature is between 0°C and +45°C
before turning on the device.
Connection and clock set
• Plug the adapter into a 100~240V AC outlet and the other end in the DC in (10).
• The electronic clock will turn ON and the clock shows "0:00".
• The LCD backlight will light up and shows "PLZ SET TIME". Press [q /Mode] button to turn ON
the radio. The radio will start scanning the DAB channels automatically in the first time:
• The time will sync to the time broadcasted by DAB, by default.
• O nce the scan is finished, it will display the number of radio stations received, and start to play the first station
automatically.
• T o explore the stations that have been found, you need to press either the 'Down or 'Up' key to see the next or
previous station. When you find a radio station that you would like to listen to, then press the [
to select the station. If you don't press the select key, the radio will switch to the new station automatically after 5
seconds.
• When you start up the radio again, the radio plays the same mode and same station as last listened.
Adjusting the volume
Press [ /Select ] button, then press [Up] or [Down] to increase and decrease the volume.
Changing radio mode (DAB /FM)
+
Select the DAB + /FM mode by long pressing the [ q /Mode ] button.
Adjusting the backlight
There are 3 levels of brightness available for selection.
• To adjust the brightness level, turn the radio to Standby and use the up/down button to adjust.
• You can set the time out interval under the <Time out> setting menu. Long press the Info/Menu button to access the
main menu, choose <System> and select <Timeout> option to do the setting.
Remark: Refer to the System section for the options available of Time out.
DAB mode
+
The Info/Menu button enables you to change some of the default settings of your radio, so that it works just the way you
want it to. To enter into the main menu, hold and press the Info/Menu button for 3 seconds, it will enter into the main
menu below. You can press [Up] or [Down] to choose different submenus. Whenever you want to exit the menu, long
pressing the Info/Menu button to return the previous menu.
Full scan
It searches all stations available in your location; it may take 1-3 minutes to complete the scan.
Manual Tune
1. U sing the manual tune feature, you can manually tune the receiver. This can help you when aligning your aerial or
when adding stations that were missed while auto tuning.
2. P ress the [Up] or [Down] button to scroll through the digital radio frequencies and select the frequency you want to
fine tune.
Maintenance.
If you have problems, do not attempt to repair the unit yourself.
Return it to your Caliber Europe BV dealer for servicing.
Placement.
Place the product on a flat surface. Provide enough space
around the product for sufficient ventilation.
Heat.
Do not locate the appliance in the vicinity of a heat surface or
in direct sunlight.
/ Select] button
Alarm:
There are 2 alarms available on the radio. Follow the steps below to set the alarm.
1. Turn the radio on, hold the [ Sleep/Alarm/Snooze ] button to enter the Alarm setting. You can also set the Alarm when
the radio is on Standby too. Under Standby, long pressing the Sleep/Alarm/Snooze button and the Alarm wizard will
pop up.
If you want to set the Alarm 2, simply press the [Up] or [Down] button. Then press [
setting.
2. The display shows "Inactive", press [Up] or [Down] to show "active" on the display,
3. Then press [ / select ] to confirm to go to next step to set the Time. Press [Up] or [Down] button to adjust the Hour
and press [ / Select ] button to confirm, then set the minute accordingly and confirm to move to next step.
4. I t comes to choose the source of alarm. You can set the alarm to activate in Buzzer, DAB Radio or FM radio. If you
choose DAB or FM, you can either choose the preset station or the last listened station as the alarm source.
5. T he next setting is to select volume level of the alarm you like. Adjust it by pressing [Up] or [Down] button. Then press
[ / Select ] to move to next step.
6. The display shows "Duration", it means how long you want to keep the alarm sounds over the time period. You can
choose from 15, 30, 45. 60 and up to 90 minutes. Confirm and move to next step.
7. It comes to set the schedule of the alarm. You can choose the option of Daily/Once/Weekends/Weekdays
8. Press [ / Select ] to confirm the option, then the display will show as below
Sleep /Alarm/Snooze
When the alarm is activated, you can press [ Sleep/Alarm/Snooze ] to active snooze to delay the alarm and it will turn on
again in 9 minute interval. If you want to turn off the alarm, just simply press [ q / Mode ] button, then the alarm will be
turned off and go to standby mode.
FM Mode
1. When you are in DAB mode, hold the [ q /Mode ] button to change to FM mode.
2. P ress and hold the [Up] or [Down], your radio will scan in an upward direction or downward direction and stop
automatically when it finds a station.
3. A fter a few seconds, the display will update. The display will show the station name and it will display the RDS (Radio
Data System) information if available.
4. I f press the [Up] or [Down] button, then your radio will scan upward or downward 0.05MHz.
Note: If reception is still poor adjust the position of the aerial or try moving the radio to another location.
Storing radio stations
1. The radio can store up to 10 DAB and 10 FM stations in its preset memories for instant access to your favorite
stations.
2. Tune your radio to the station that you wish to preset.
3. Hold and press "Preset" to enter the preset menu, the display will pop up as below. The <P01Empty> will blink.
4. T hen press [Up] or [Down] button to choose the number you want to preset, press [ / Select ] to confirm. The
display will show "P X Saved", where "X" is the number of the preset (1-10).
Recall stored station
Press the [Preset] button, then the display will show "P01: (Empty)" or "P01: station name" (where station name is the
station has been saved), press [Up] or [Down] button to select the station you want to listen, and then press the [
Select] button to confirm to play.
Note: If no station has been stored under the preset, the display will show "Px: (Empty)" and then revert to the
previously selected station after a few seconds.
Factory Reset:
It can reset your radio and restore all the settings to the original factory settings.
Long press [Menu] to enter the submenu <system> and choose <Factory Reset>, then press [
confirm. Follow the wizard on the display to complete the reset. The radio will restart by itself.
/ Select ] to start the alarm
/
/ select ] button to