Publicidad
1.
Power Input (power In)
2.
Link current
/ Link corriente
3.
DMX Output
/ Salida DMX
4.
Safety Key
/ Llave de seguridad
5.
Operating Channels of DMX
6.
Activation button
/ Botón de accionamiento
7.
Activation Led indicator
8.
Mode button
/ Botón modo
9.
Safety channel for DMX
10.
On/Off switch to unlock the Safety Channel
11.
Push button to unlock the Safety Channel
12.
Led indicator of unlock safety channel
SETUP AND OPERATION
1.
Place the 8 CHANNEL DMX PUSHER on a fl at, stable surface. Connect the power supply cable
(not included) using the POWER IN connector (1).
2.
Make sure that the safety key (4) is in OFF position.
3.
Connect the DMX machines which you want to control to the DMX output connector (3). You
can use either of the 3-pin or 5-pin DMX out connectors according to your needs.
4.
Turn On now the 8 CHANNEL DMX PUSHER device (4).
5.
Assign the OPERATING DMX channels according to the machines you want to control using
the buttons "UP" and "DOWN". Make sure that the channel selected is free and that there is no
repeated channel. A channel repeated might create confl ict and have a malfunction.
The 8 CHANNEL DMX PUSHER off ers 3 shooting modes for each operating channel: On/off switch
(switch), Push button (fl ash) and burner (burnt).
SWITCH MODE It works as a switch, that is, On/Off position. It is ideal for long-lasting eff ects (lights,
blowers, etc...) which require to be activated for some more than just a few seconds.
1.
To activate the switch mode, press the mode button (8) until the display shows "S"(just before
the number of DMX channel).
2.
Press the Activation button SWITCH / FLASH" (6) to activate the machine connected to that
channel. The Activation Led indicator (7) will light on.
3.
To turn off the switch, press again the Activation button SWITCH / FLASH" (6)
FLASH MODE (FLASH) It works as a pusher. It is ideal for short duration eff ects as for instance CO2
Jets..
1.
To activate the Flash mode, press the mode button (8) until the display shows "F"(just before
the number of DMX channel).
2.
Press and keep pressing the Activation button SWITCH / FLASH" (6) to activate the machine
connected to that channel. The machine will remain activated as long as you keep pushing the
button. And the Activation Led indicator (7) will light on also while pressing. Once you stop
pressing the button the machine on that channel will turn off .
BURNT MODE. In this mode, the device only allows to activate 1 single time the machine/s
connected to that channel. Furthermore, the display shows you which are the channels which have
been already fi red. (Burnt). This becomes very useful when fi ring confetti machines.
1.
To activate the Burnt mode, press the mode button (8) until the display shows "b" (just before
the number of DMX channel).
2.
Press the Activation button SWITCH / FLASH" (6) to activate the machine connected to that
channel. The Activation Led indicator (7) will light on. The machine will remain activated as long
as you keep pushing the button, and the Activation Led indicator (7) will light on. The diff erence
is that in this BURNT mode, after the 1st activation the 8 CHANNEL DMX PUSHER will block
/ Entrada de corriente (powercon)
/ Canales operativos DMX
/ Led indicador de accionamiento
/ Canal de seguridad DMX
/ Interruptor de desbloqueo de canal de seguridad
/ Pulsador de desbloqueo de canal de seguridad
/ Led indicador de desbloqueo de canal de seguridad
/ MONTAJE Y OPERATIVA
INSTRUCTION MANUAL
8 CHANNEL DMX PUSHER
Publicidad
