Seamaid 501818 Manual De Instrucciones Y Mantenimiento página 7

UK
IMPORTANT: this instruc�on manual contains highly
important informa�on about safety measures to be taken
when installing and commissioning the device. It is therefore
important for you to read these instruc�ons before assembling and
opera�ng the product. Please keep this manual for later use. Lack
of compliance with the instruc�ons stated in this manual during
the installa�on, opera�ng and maintenance phases shall relieve
the manufacturer or distributor of any liability in the face of
damages caused to people, to the product or to the installa�on
site, and will result in you losing the warranty.
1. GENERAL INFORMATION
This remote control switch was designed for indoor and outdoor use. It is a class
III remote control accessory with Safety Extra Low Voltage of ~12V(AC) or ⎓
14/24V(DC). It is only compa�ble with LED ligh�ng systems of iden�cal voltage.
This remote control switch boasts an IP65 protec�on level. This remote control
switch also complies with interna�onal electrical safety standards - namely the IEC
61059 – 1 interna�onal standard: 2002 + A2.
2. INSTALLATION
Correct installa�on requires for the plug powering the ligh�ng system to be
protected by a residual current device, with a maximum intensity of 30 mA. This
remote control switch can only be connected to a double-insulated transformer
or a double-insulated compa�ble stabilised safety power source. The remote
control switch must be posi�oned ver�cally along a smooth wall, with its antenna
poin�ng upwards. For improved range outdoors, we recommend installing it with
a direct view of the remote control. The manufacturer can in no way be held
responsible for the assembly, installa�on or opera�on of the product if it was
manipulated or if non-provided electrical components were added.
3. ASSEMBLY AND REPLACEMENT
Prior to installa�on, it is important to check that the connected projectors' total
power remains lower than the maximum power authorised by the channel and
control switch, and to refer to the assembly guide.
4. MAINTENANCE
This control switch does not require any form of maintenance. When the red LED
on the remote control no longer lights up, its 12V MN23 ba�ery needs to be
replaced. If the product malfunc�ons, please contact either our customer service
department, or that of your retailer.
5. USAGE
The system works like a switch, operated by a remote control. When first using the
remote control, you will need to configure it with its receiver - already integrated
in the casing.
Opera�ng the remote control:
Stop/Start: press on the O bu�on
Change programme: press X the bu�on
Channel synchronisa�on (4-channel switch)
To synchronise the channels together, press on the X3 and X4 bu�ons at the same
�me for 20 seconds un�l the lights start flashing.
To desynchronise the channels, press on the O3 and O4 bu�ons at the same �me
for 20 seconds un�l the lights start flashing.
The presence of metal and electrical appliances may interfere with the
connec�on between the remote control and the casing. If this happens, a be�er
loca�on should be found for installing the casing, or an op�onal external wire
antenna should be added.
6. SAFETY WARNINGS
- Before working on the system, it must be unplugged from
the electrical network
- Never work on the device with wet feet
- All accident preven�on standards currently in force must be
complied with
- IEC 364-7-702 standards in par�cular must be complied with:
ELECTRICAL INSTALLATIONS INSIDE BUILDINGS. SPECIAL
INSTALLATIONS. POOLS.
- The person in charge of assembly must be suitably qualified
for the job.
7. WARRANTY
This remote control switch is guaranteed against any material and/or
manufacturing defects (electronic components) for 2 years star�ng from the
date of delivery. (Substan�a�ng documents must be preserved). It is not
guaranteed against breakage caused by an external impact, a short circuit or
excessive screwing, nor against power surges caused by the main power
network. (In this case, the home insurance policy will kick in). This warranty is
valid under the strict condi�on that the assembly and maintenance instruc�ons
are complied with. Within the framework of this warranty, the manufacturer or
distributor's only obliga�on will be to have their a�er-sales service replace or
repair the product or component recognised as defec�ve for free (the choice is
theirs to make). Any other costs are to be covered by the purchaser. To benefit
from this warranty, products must first be sent in to the manufacturer or
distributor's a�er-sales service; their consent is mandatory if the product is to
be replaced or repaired. The warranty shall not apply in the case of a visible
defect. Defects and deteriora�ons caused by normal wear, malfunc�ons
resul�ng from non-compliant assembly and/or usage, and product
modifica�ons made without the manufacturer's prior wri�en consent are also
excluded from the warranty.
8. ENVIRONMENTAL INFORMATION
In accordance with European Direc�ve 2002/96/EC, pertaining to waste
electrical and electronic equipment (WEEE), the consumer must return any
used products to suitable collec�on points.