Battery Charging - Swiss Made FELCO 880 Serie Manual De Instrucciones

CAUTION
During initial use, if you try to work with your pruning
shear 15 without prior charging of the battery 09, the pruning
shear will not work.
As battery 09 has been set automatically to "storage" mode,
the first thing to do is to connect battery 09 to charger 11. To
do this proceed as follows (see Figure B on page 4):
1. Connect battery 09 to charger 11.
2. Connect the power cord 13 adapted to your supply grid
to charger 11.
3. Connect charger 11 to the power grid.
4. The indicator light 12 on the charger 11 turns red.
5. Once battery 09 is charged, the indicator light 12 turns
green.
6. Disconnect charger 11 from the power grid.
7. Disconnect battery 09 from charger 11.
8. Verify that operation switch 07 is set to "OFF" position.
9. Connect the plug of the battery 09 to one of the two
corresponding jacks of the control housing 04. Note:
Connection is functional on both jacks.
10. Connect the power cord of the pruning shear 02 to the
pruning shear 15. Note: If you are left-handed, route the
power cord of the pruning shear through the left side of
the rucksack 03.
USE
(See illustration C on page 5).
1. Pre-set the lap belt.
2. Attach the holster 10 on the belt on the left or right side
depending on whether you are left or right handed.
3. Put on the rucksack.
4. Fasten the lap belt.
5. Adjust the lap belt at waist height.
6. Adjust the shoulder straps.
7. Close the chest strap.
8. Adjust the chest strap.
9. Hold the pruning shear 15 in your hand, toggle switch 07
of the remote housing 06, from the "OFF" to the "ON"
position (the display 08 of the remote housing 06 is
activated).
10. Press once on trigger 16 and blade 17 opens. (Blade 17
opening and locking is proportional to the pressure
applied by the finger). When activating the tool, you will
hear audio signals (beeps). In order to interpret them,
refer to chapter: "AUDIBLE NOTIFICATIONS" in this user
manual.
11. In order to stop the pruning shear 15, close the blade 17
using the trigger 16, keep the blade closed, toggle
switch 07 to the "OFF" position (the display 08 of the
remote housing 06 closes). It is also possible to
temporarily stop the pruning shear 15 using option
"STAND-BY MODE" see "REMOTE HOUSING".
NOTES
• In order to save the energy fed by battery 09 and to
also ensure maximum autonomy for the pruning
shear 15, consider using option "semi-opening" which is
adjustable to 50%, 60%, or 70%. (Refer to chapter
"REMOTE HOUSING", "SEMI-OPENING SETTING"
MENU). This option offers precious time-saving when
pruning small diameters. (Only available with
FELCO 801 or FELCO 820).
• If the wood is too thick, the pruning shear 15 stops in
the closing direction. Only opening is possible.
ADVICE FOR USE
• You must take all precautions to prevent the
entanglement of the pruning shear power supply
cord 02 in the branches. In order to do this, prefer
routing cord 02 along your shoulder and not around
your waist. In any case, if you wish to use the cord
around the waist, exit the cord 02 either from the top, or
from the left or right opening on the lower part of the
rucksack (depending on whether you are right- or left-
hander), then attach the cord 02 to the arm using an
arm band (ref. 800/301, available as an option at your
preferred authorized dealer), or route it under your
sleeve.
• In cold or wet conditions, protect "POWERPACK
FELCO 880" carrying it under your raincoat.
• If required, you may increase the autonomy of your
POWERPACK FELCO 880 (Refer to illustration D on
page 5) using a second battery. The second battery
may be connected, in parallel, to the second jack of the
control housing 04. On the other hand, if you wish to
have a lighter rucksack, it is recommended to replace a
discharged battery 09 with a second battery 09
previously charged.
NOTES
• The battery(ies) is discharged when the indicator of the
remote housing 08 indicates the following:
B 1 - B 2 : - - - - - - - - - -

BATTERY CHARGING

1. Proceed as described in Section: "INITIAL USE".
2. When the indicator light 12 on charger 11 becomes red,
battery 09 is being charged. The average charging
duration is 2 hours. Charging is completed when the
indicator light 12 on the charger 11 turns green. A second
check can be done by means of connecting the
battery(ies) 09 to control housing 04 and activating
pruning shear 15 with the switch 07. The display 08 of
the remote housing 06 displays the following:
with a battery connected on the right jack of the control
housing 04:
B 1 - B 2 :
with a battery connected on the left jack of the control
housing 04:
B 1 - B 2 : - - - - - - - - - -
- 9 -
- - - - - - - - - -
         
- - - - - - - - - -
         