3-Way (Two Location)
120VAC, 60Hz
Slide Fan Speed Control
Cat. Nos. 6637, 5A
INSTALLATION INSTRUCTIONS
Tripolaire (Deux emplacements)
120 V c. a., 60 Hz
Commande à glissière
de vitesse de ventilateur
Nº de cat. 6637, 5 A
DIRECTIVES D'INSTALLATION
Tres Vías (Dos Ubicaciones)
120VCA, 60Hz
Control Deslizante
p/Velocidad de Ventilador
Nos. de Cat. 6637, 5A
INSTRUCCIONES DE INSTALACION
DI-000-06637-20B
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for
the benefit of anyone else that this product at the time of its sale
by Leviton is free of defects in materials and workmanship under
normal and proper use for five years from the purchase date.
Leviton's only obligation is to correct such defects by repair or
replacement, at its option, if within such five year period the
product is returned prepaid, with proof of purchase date, and a
description of the problem to Leviton Manufacturing Co., Inc.,
Att: Quality Assurance Department, 59-25 Little Neck Parkway,
Little Neck, New York 11362-2591. This warranty excludes and
there is disclaimed liability for labor for removal of this product or
reinstallation. This warranty is void if this product is installed
improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under
normal operating conditions or not in accordance with any labels
or instructions. There are no other or implied warranties of any
kind, including merchantability and fitness for a particular purpose,
but if any implied warranty is required by the applicable jurisdiction,
the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to
five years. Leviton is not liable for incidental, indirect, special, or
consequential damages, including without limitation, damage to,
or loss of use of, any equipment, lost sales or profits or delay or
failure to perform this warranty obligation. The remedies provided
herein are the exclusive remedies under this warranty, whether
based on contract, tort or otherwise.
For Technical Assistance Call:
1-800-824-3005 (U.S.A. Only)
www.leviton.com
DI-000-06637-20B
•
Leviton's Decora
®
style design
•
Operates any number of ceiling fans up to rating limits
•
Fits standard wall boxes
WARNING:
TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
WARNING:
IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICIAN.
WARNING:
TO AVOID OVERHEATING AND POSSIBLE DAMAGE TO THIS DEVICE AND OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE, FLUORESCENT LIGHTING, A MOTOR- OR A
TRANSFORMER-OPERATED APPLIANCE OTHER THAN APPROPRIATE CEILING FANS.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, THIS CONTROL IS TO BE USED WITH A CEILING FAN THAT IS MARKED AS SUITABLE FOR USE WITH A SOLID-STATE FAN SPEED
CONTROL AND IS RATED 120 VOLTS, 5 AMPERES MAXIMUM.
WARNING:
FOR USE ON CEILING PADDLE FANS WITH SPLIT-CAPACITOR OR SHADED POLE MOTORS ONLY. PLEASE REFER TO FAN MANUFACTURER'S INSTRUCTIONS OR RATING LABELS ON THE
MOTOR TO CONFIRM TYPE. USE WITH ANY OTHER TYPES OF MOTORS OR EQUIPMENT MAY CAUSE OVERHEATING AND/OR DAMAGE TO THE MOTORS OR EQUIPMENT.
OTHER CAUTIONS:
1. USE ONLY ONE SPEED CONTROL IN A 3-WAY CIRCUIT. THE REMAINING 3-WAY SWITCH WILL TURN ON FAN AT SPEED SELECTED AT THE CONTROL.
2. DISCONNECT POWER WHEN SERVICING FIXTURE.
3. USE THIS DEVICE ONLY WITH COPPER OR COPPER CLAD WIRE. WITH ALUMINUM WIRE USE ONLY DEVICES MARKED CO/ALR OR CU/AL.
MULTI-FAN CONTROL:
Any number of fans of the same type may be controlled by a single fan speed control provided that the total amperage of the fans does not exceed the amperage rating of the fan speed control.
GANGING/DERATING:
When combinations of dimming and/or speed controls are installed in a ganged wall or outlet box, derating is required. When two devices are mounted in a ganged box, the maximum load per device shall not exceed 4.1A
or 500 watts. When three or more devices are mounted in a ganged box, the maximum load shall not exceed 3.3A or 400 watts.
TO INSTALL:
WARNING:
1.
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
2. Remove existing wallplate and switch, if applicable.
3. Remove 5/8" (1.6 cm) of insulation from each circuit conductor. Make sure the ends of wires are straight.
4. Connect wires per WIRING DIAGRAM as follows: Twist strands of each lead tightly together and, with circuit conductors, push firmly into appropriate wire connector. Screw connectors on clockwise making sure no
bare conductors show below the wire connectors. Secure each connector with electrical tape.
IMPORTANT: This model incorporates a trim adjustment which will allow the installer to precisely set the low end of the fan speed range to suit each installation. This adjustment is preset at the factory and should require
no further adjustments for most installations. If adjustment is required, follow these steps, if not go to step 8.
5. Restore power at circuit breaker or fuse. Holding speed control securely by its insulated case, position the fan speed control so that the rocker switch is at the bottom. Make sure fan is rotating by moving ON/OFF
rocker switch to ON position and sliding control lever to a middle position. The rocker switch below the slider provides positive ON/OFF switching.
6. The trim adjustment is located at the top of the fan speed control back cover. Interrupt power by moving ON/OFF rocker switch to OFF position. Slide control bar DOWN to lowest position (closest to ON/OFF rocker
switch).
7. After fan stops rotating, restore power by moving ON/OFF rocker switch to ON position (keep control bar down at lowest position). Fan should rotate at low end speed after power has been restored. If fan blades are
not rotating, adjust low end (slowest) fan speed as follows:
A. Insert a small screwdriver into trim slot.
B. Turn clockwise to increase fan speed, counterclockwise to lower fan speed. The low end trim is now set.
8. TURN OFF POWER. Installation may now be completed by carefully positioning all wires to provide room in outlet box for fan speed control. Mount fan speed control into box with mounting screws supplied. Attach wallplate.
9. Restore power at circuit breaker or fuse. INSTALLATION IS COMPLETE.
Slide bar control up or down for desired fan rotation speed. ON/OFF rocker switch will turn fan ON at speed set by slide bar.
•
Style de la gamme Decora
®
de Leviton
•
Compatibilité à de nombreux modèles de ventilateurs dans les limites prescrites
•
S'adapte à toute boîte simple standard
AVERTISSEMENT :
INSTALLER OU UTILISER CONFORMÉMENT AUX CODES DE L'ÉLECTRICITÉ EN VIGUEUR.
AVERTISSEMENT :
À DÉFAUT DE BIEN COMPRENDRE LES DIRECTIVES SUIVANTES, FAIRE APPEL À UN ÉLECTRICIEN QUALIFIÉ.
AVERTISSEMENT :
POUR ÉVITER LA SURCHAUFFE OU L'ENDOMMAGEMENT ÉVENTUEL DE CE DISPOSITIF ET D'AUTRES APPAREILS RACCORDÉS, NE PAS L'INSTALLER POUR COMMANDER UNE
PRISE, UN LUMINAIRE FLUORESCENT, OU UN APPAREIL MOTORISÉ OU À TRANSFORMATEUR AUTRE QU'UN VENTILATEUR POUR PLAFOND APPROPRIÉ
AVERTISSEMENT :
POUR RÉDUIRE LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, N'UTILISER CE DISPOSITIF NE DOIT ÊTRE UTILISÉ QUE POUR LES VENTILATEURS DE PLAFOND IDENTIFIÉS
COMME ÉTANT CONÇUS POUR PERMETTRE UNE RÉGULATION DE LES VITESSE ET DOIVENT AUSSI AVOIR DES VALEURS NOMINALES MAXIMALES DE 120 VOLTS C.A., 5 AMPÈRES.
AVERTISSEMENT :
NE PEUT ÊTRE UTILISÉ QU'AVEC DES MOTEURS À CONDENSATEUR OU À BAGUE DE DÉPHASAGE; VEUILLEZ CONSULTER LES DIRECTIVES DU FABRICANT DE VENTILATEURS, OU
L'ÉTIQUETTE SIGNALÉTIQUE APPOSÉE SUE LE MOTEUR, POUR EN CONFIRMER LE TYPE; UNE UTILISATION AVEC TOUT AUTRE TYPE DE MOTEUR OU D'APPAREIL POURRAIT CAUSER LA SURCHAUFFE,
VOIRE MÊME LE BRIS, DE CE MOTEUR OU DE CET APPAREIL.
AUTRES MISES EN GARDE :
1. N'INSTALLER QU'UN SEUL COMMANDE DE VITESSE PAR CIRCUIT; L'INTERRUPTEUR À TROIS VOIES SITUÉ À L'AUTRE POINT DE COMMUTATION DÉMARRER LE VENTILATEUR À LA VITESSE INDIQUÉS
PAR LE COMMANDE.
2. LORS D'UNE VÉRIFICATION D'APPAREILS, COUPER L'ALIMENTATION.
3. UTILISER CE DISPOSITIF SEULEMENT AVEC DU FIL DE CUIVRÉ; POUR LE FIL EN ALUMINIUM, UTILISER SEULEMENT LES DISPOSITIFS MARQUÉS CO/ALR OU CU/AL.
COMMANDE DE PLUSIEURS VENTILATEURS : un seul dispositif peut commander plusieurs ventilateurs, à condition que la puissance totale de ces derniers ne dépasse pas les valeurs nominales de la commande.
GROUPEMENT/ABAISSEMENT : lorsque des commandes de gradation de lumière ou de vitesse sont combinées, on doit opérer un certain déclassement; quand deux unités sont combinées, la charge maximale par
unité ne devra pas excéder 4,1 A ou 500 W.; quand plus de deux unités sont combinées, cette charge ne devra jamais dépasser 3,3 A ou 400 W.
INSTALLATION :
AVERTISSEMENT :
1.
POUR ÉVITER LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURE MORTELLE, COUPER LE COURANT AU FUSIBLE OU AU DISJONCTEUR ET S'ASSURER QUE
LE CIRCUIT SOIT BIEN COUPÉ AVANT DE PROCÉDER À L'INSTALLATION.
English
FEATURES
•
Slide control for easy and precise operation
•
Minimum Speed Adjustment
INSTALLATION INSTRUCTIONS
OPERATION
Français
CARACTÉRISTIQUES
• Commande à glissière pour un réglage simple et précis
• Réglage de la vitesse minimale
DIRECTIVES D'INSTALLATION