Publicidad
Care and
maintenance
METAL PARTS (STRUCTURE AND TOP)
This product has been made with resistant materials of the
highest quality. With correct care and maintenance you will
be able to enjoy it for many years. However, dirt or other
contaminants and bad use could damage it.
For the optimal conservation of pieces manufactured in
steel and stainless steel, especially if they are exposed to
the elements, periodic maintenance is advised.
For maximum resistance to corrosion, steel surfaces must
always be kept clean. This maintenance must be tailored
to the conditions to which your product is exposed (dust,
dirt, humidity in combination with heat, salty or potentially
corrosive environments, etc.). This can vary from one to four
times a month, in normal settings, or up to once a day in
cases of unhygienic or very rough conditions.
You must be the one who adjusts and evaluates the
periodicity of the maintenance according to how the
material reacts, increasing or reducing it depending on
what is necessary for proper product care. In any case, we
recommend cleaning it at least once a week, as a starting
point.
Therefore, it's important to keep the product clean.
Please follow these simple instructions to keep the product
in good condition:
• For cleaning steel, use only a cloth dipped in warm water
and mild soap. Never use abrasive soaps or detergents, as
they can leave scratches and produce discoloration.
• Rub gently with a damp cloth. Rinse and wring the cloth
frequently, to keep it moist. Make sure to rinse well and dry
with another cloth.
• If the surface is glossy, you must wash it along the grain,
to avoid scratching the surface. On polished surfaces, you
must previously remove dust to avoid scratching the surface.
• If the event of a spill, clean the stain quickly.
• If you are unable to remove the stains with a damp cloth,
apply a metal cleaner to the surface with a cloth. Read the
instructions for the cleaner carefully, and test it first on an
inconspicuous spot. Make sure to rinse well and dry with
another cloth.
• When the product is extremely dirty, with stains,
incrustations, or signs of surface discoloration due to long
periods of neglect, or poor maintenance, we recommend
contacting professionals to restore the surface's initial
appearance.
MARBLE (TOP)
Wipe up spills immediately with a soft, clean and
dry
cloth.
Be
especially
alkaline
or
acidic
liquids,
Apply
protective
pads
Plec table — User's manual / Manual de usuario
careful
with
extremely
which
can
damage.
to
undersides
of
items
being
displayed
Do not use ammonia, bleach and highly alkaline or acidic
cleaners, which can break down the protective sealant on
marble surfaces.
For daily cleaning we recommend the use of only neutral PH
soap or detergents for marble on a soft, clean and dry cloth.
Carefully read the instructions on the detergent's label and,
in doubt, perform a test on a small, inconspicuous area.
IF THE PRODUCT IS USED OUTDOORS, KEEP IT CLEAN AND
IN GOOD CONDITION, FOLLOWING THESE INSTRUCTIONS
MORE FREQUENTLY.
WHEN THE PRODUCT IS KEPT OUTDOORS AND IS NOT
USED FOR PROLONGED PERIODS, WE RECOMMEND YOU
TO USE THE PROTECTIVE COVER.
Mantenimiento
y limpieza
METAL (ESTRUCTURA Y SOBRE)
Este producto está realizado con materiales de alta calidad
muy resistentes. Con un mantenimiento adecuado podrás
disfrutarlo durante años. Sin embargo, la suciedad y el mal uso
pueden dañarlo. Por ello debes mantener el producto limpio.
Para una buena conservación de las piezas fabricadas en acero
y aceros inoxidables, especialmente si están a la intemperie, es
conveniente realizar un mantenimiento periódico.
Para una máxima resistencia a la corrosión, la superficie de
acero debe mantenerse siempre limpia. Este mantenimiento
deberá adaptarse a las condiciones ambientales a las que se
encuentre sometido tu producto (polvo, suciedad, humedad en
combinación con calor, ambientes salinos o potencialmente
corrosivos, etc....). Esto puede variar de una vez a cuatro veces
al mes en ambientes normales o puede ser una vez al día en
caso de situaciones muy agresivas.
Debes ser tú mismo quien ajuste y valore la periodicidad del
mantenimiento en función de cómo reaccione el material,
acortándola o alargándola para conseguir un correcto cuidado
del producto. En cualquier caso, te recomendamos realizar
una limpieza al menos una vez por semana, como punto de
partida.
Sigue estas sencillas instrucciones para mantener el producto
en buenas condiciones:
• Para la limpieza del acero, usa únicamente un trapo bañado
en agua tibia y jabón suave. No uses jabones o detergentes
abrasivos ya que podrían dejar rasguños o decoloraciones.
• Frota suavemente con el paño húmedo. Enjuaga y escurre el
paño frecuentemente, para mantenerlo húmedo. Asegúrate de
enjuagar bien y secar con otro trapo.
• Si la superficie es satinada, el movimiento del lavado deberá
ser paralelo a la dirección del satinado, así evitarás el rayado
de las superficies por el polvo. En las superficies pulidas
debes eliminar previamente el polvo para evitar el rayado de
la superficie.
• Si por accidente cae o se derrama algún líquido, limpia las
manchas lo más rápido posible.
• Si con un trapo húmedo no consigues eliminar las manchas,
2
on
marble
surfaces.
Publicidad
