Illustrated Description; Operating Instructions; On / Off; Troubleshooting - stayer VENTO 2400 B Manual De Instrucciones

Extend the tube 1 to its maximum length by pulling its end
until the holes 17 in the support of the fixing devices of the
tube 1 can be seen.
Insert the two fixing plugs 18 that are supplied, ensuring
that they enter into the support.
Place the channeling tube 1 on the motor set 15, ensuring
that the holes 17 in both parts engage.
Fix the two pieces by means of the two screws and the two
nuts that are supplied.
Collection Bag (VENTO2400B)
When aspiring, the collector bag 3 must be compulsorily
used. To assemble the bag 3 at the motor set 15:
1. Place the circular support for the bag 3 at the air
outlet hole 16 ensuring engagement of the holes.
2. Fix the support by inserting it into the guides and
tighten each of the two self-screwing screws as
supplied.
3. Secure the bag 3 to the support 16 by tying it with the
rope as included.
4. The bag 3 has two fastening loops made of fabric.
Fasten them to the fastening hooks at the motor set.
5. Always keep the bag 3 empty when the machine is not
in operation.
Machine holding belt
The equipment includes a belt 4 for ergonomically
positioning the machine. For assembly of the holding belt 4:
- Open the belt 4 by pushing its lock.
- Pass the belt 4 through the fastening ring 17.
- Adjust the length of belt 4 according to the user's
stature and depending on how it is held.
Cord restraint (Fig. 9)
- Hook the loop in the extension cord over restraint 5 as
illustrated.
- Pull tight to secure the extension cord.
Emptying of collection bag (Fig. 12)
Switch off the tool and disconnect the plug
- Wait until the impeller comes to a standstill before
removing the collection bag from the tool.
- Open the zipper of the collection bag and empty it
completely
- Compostic material does not belong with domestic waste

3.3 Illustrated description

1 Lower blower/suction tube
2 Upper blower/suction tube
3 Collection bag
4 Shoulder strap
5 Cord restraint
6 On/off switch
7 Switch for selecting operating mode
8 Supporting wheels
9 Ventilation slots
10 Main handle
11 Guide handle
ENGLISH
15
12 Fastening screws (4)
13 Vacuum opening
14 Blower opening
15 Motor set
16 Suction socket
17 Fastening holes
18 Fixing plugs (VENTO2400B)

4. Operating instructions

4.1 On / Off (Fig. 10)
Switch on/off the tool by pushing switch
position
Before switching on the tool, ensure that it is not
in contact with any object.
After switching off the tool the motor continues
to run for a few seconds.
Blowing
Select blowing mode with switch 7 as illustrated (only when
tool is switched off)
Vacuuming
- Ensure that collection bag 3 is attached to the tool (for
mounting see Fig. 1-8
- Select vacuuming mode with switch 7 as illustrated (only
when tool is switched off)
Do not vacuum solid objects such as stones,
broken glass, pieces of metal
- Do not vacuum liquids.
- Do not vacuum large volumes of leaf material at one time
thus avoiding clogging of the vacuuming opening and
blocking of the shredder impeller.
- The shredding intensity depends on the size of the leaf
material and its residual moisture.
When the tool suddenly stops, immediately
switch it off, disconnect plug from power source,
and remove any jammed material between
shredder impeller and housing.
- Regularly empty collection bag 3 (the vacuum capacity
decreases considerably when the collection bag is full)
Holding and guiding the tool (Fig. 11)
While working, always hold the tool at the grey-
coloured grip area(s)
- Use supporting wheels 8 for easy guiding the tube along
the ground
- For optimal results keep a 5 - 10 cm distance to the ground

4.2 Troubleshooting

The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify and
correct the problem, contact your dealer or service station)
15
6 (Fig. 10)
)
in "I"/"O"