Trouble Eshootin - Velleman AVMOD16N1 Manual Del Usuario

8. . System m Installa
Se elect the ch annel to be
rec ceiver are s set to the s
Ch hannel Sel lection on
To set the channel on
(e.g. ballp point pen). T
activated a at one time
Camera set to chan
Ch hannel Sel lection on
The receiv ver can rece
a. Manua l Channel
Set the channel on
channe l always re
camera and the re
Receiver set to chan
b. Auto-s scan Mode
If you w wish to use
automa atic scan mo
receive r. The scan
be scan nned, simpl
position n.
Came era 1
9. . Trouble eshootin
If you obtain no or a dis
• Are the po ower adapte
• Is the mon nitor or TV
• Are the ap ppropriate c
• Is there a microwave
it out of th he path or r
• Is the dist ance betwe
• Is the rece eiver anten
10 0. Tech hnical sp
Ca amera
Po ower Supply y
Po ower Consu mption
Di mensions ( (on stand)
Op perating Te mperature
Im mage Senso or
Re esolution
Le ns
Mi n. Illumina tion
Us se this dev vice with o
th e event of f damage
09/ /09/2010
AVMOD16
ation
e used on b both the ca
same chann nel (1, 2 or
the Came era
n the came era, place th
The selecte ed channel
e.
nnel 1 Camer
the Recei iver
eive up to t three came
Selection
n the receiv ver using a
mains activ ve. Only on
eceiver are set to the
nnel 1 Receive
several ca meras (up
ode. Define e a channel
n mode will switch cha
y de-activa ate it by pla
Ca amera 2
g
storted pict ture, check
ers for cam mera(s) and
switched o on?
channels se elected / sw
e oven or ot ther disturb
relocate ca mera(s) or
een the cam mera and th
na position ned for opti
ecificatio ons
7.5VDC, 200mA
(included d)
1.3W
100 x 95 x 40mm
0-50°C ; 32-122°F
1/3" colo our CMOS
450 horiz zontal TV li
8mm
8 Lux
original ac ccessories
or injury r resulted fr
6N1 - AVM MOD16CCN
mera and r receiver. Ma
r 3).
he switch to o the desire
always rem mains active
a set to cha annel 2
eras, even i n scan mod
pointed ob bject (e.g.
ne channel may be act
same chan nel (1, 2 o
er set to ch hannel 2
to 3 units) , you can a
l for each c camera and
annels each h 5 seconds
acing the ch hannel swit
Camera
the followi ing:
receiver c orrect (volt
witched on or off?
bing device e in the sign
receiver.
he receiver r greater th
mum recep ption?
Rece eiver
Powe er Supply
Dime ensions
Oper rating Temp
Tota l Weight
Rece eption Rang
nes Video o Output
s only. Vel leman nv
rom (inco rrect) use
5
N
ake sure th he camera a
ed channel using a po
e. Only one e channel m
Came era set to c
de.
ballpoint pe en). The se
tivated at o one time. M
r 3).
Recei iver set to
allow the ch hannels to
switch on each chann
s. If you do not wish a
tch on the r receiver in
a 3 Rec
tage) and p properly co
nal path? If f so, switch
an the tran nsmission r
7. .5VDC, 600
(in ncluded)
11 12 x 62 x 1
perature 0- -50°C ; 32-
10 05g (0.25L
ge up p to 90m (3
1V Vp-p 75Ω
cannot be e held resp
e of this de evice. For
Rev . 03
and the
ointed objec ct
may be
channel 3
elected
Make sure th he
channel 3
run in
nel on the
a camera to o
to OFF
ceiver
nnected?
h it off, mov ve
range?
0mA
18mm
-122°F
B)
300Ft)
ponsible in n
more info o
n nv
©Velleman