Jacob Jensen JBXK06 Manual Del Usuario página 17

Unfold the page with the illustrations! This kettle consists of four
separate parts: Kettle (Fig. 1A), wall mount (Fig. 1B), power base with
cord (Fig. 1C) and a mounting plate with screws and plugs (Fig. 1D).
Before first use
Fill the kettle with clean water to the maximum level and boil. Discard the
water and repeat. Add a tablespoon of vinegar to the water the first time.
Instructions for use
· Fill the kettle with water to the desired level - max. 0.6 l.
The lid is opened by pressing the "OPEN" button on top (Fig. 2).
Press down the lid to close. The lid must always be closed and the
filter inserted during boiling.
· Place the kettle on the base. Connect the plug to the power socket and
press down the ON/OFF button with the diode (Fig. 3). The diode will
now illuminate. The water will boil within a few minutes depending on
the amount of water.
· When the water is boiling, the kettle automatically turns off.
Condensation might appear on the exterior. This is normal, the kettle
is not leaky. After 30 seconds the kettle can be activated again.
Do not try to switch it on before, as this might damage the kettle.
· Now lift the kettle of the base and carefully pour from the kettle.
Descaling
For descaling use a mixture of vinegar and water or a descaling remedy,
which can be bought in all supermarkets etc. (follow the instructions on
the descaling remedy).
· Mix 0.1 litre vinegar with 0.4 litre cold water.
· Fill the mixture in the kettle and switch on. Let the mixture boil twice.
To remove the last remains of limescale or vinegar, fill the kettle with
clean water to maximum and switch on. When the water has boiled, pour
away and repeat the process three times. Then the kettle is ready for use.
Caution: Do not remove limescale deposits with hard objects.
Regular descaling prolongs the service life of the kettle, ensures perfect
operation, reduces the boiling time and saves energy.
Wall mounting
· Mount the mounting plate on the wall by means of the enclosed screws
and plugs (Fig. 5).
· Fix the power base to the wall mount and "click" it on. (Fig. 6).
The cord must turn backwards against the wall, where it fits down
the hole.
· Place the wall mount across the mounting plate and push it downwards
until a "click" is heard (Fig. 7). Note: The wall mount is only intended
for this kettle incl. water. Additional weight is not allowed.
Dismounting:
· Release the power base from the wall mount by pushing the two "hooks"
(Fig. 8A) outwards and then press the power base up through the hole
with two fingers.
· Remove the wall mount from the mounting plate by pressing the button
underneath the wall mount (Fig. 8B) and then push the wall mount
upwards until it can be lifted free of the mounting plate.
Specifications:
Dimensions
Power
Power supply
Warranty does not cover
· If you fail to comply with the above mentioned.
· If the appliance is not maintained in good state of repair, has been
subject to violence or has suffered any other form of damage.
· For faults that might appear due to fault on the power line.
· If unauthorized interference has been made on the appliance.
: 162 x 214 x 130 mm
: 1370-1630 watt max.
: 220-240 Volts - 50-60 Hz
Environmental concerns and disposal
Electric and electronic appliances contain materials, components
and substances that can be damaging to people's health and to the
environment, if the waste is not disposed of correctly.
Electric and electronic appliances are marked with a crossed-out wheelie
bin symbol as illustrated below. It indicates that electric and electronic
appliances are banned from being disposed of as general household waste,
and have to be collected separately.
Please ask you dealer about current means of disposal.
- The technical specifications for this product and the contents of this
manual are subject to change without notice.
- The manufacturer and its suppliers accept no liability whatsoever for
any damage, expense, loss of profits or any other damage incurred
as a result of using this product.
15