Important Safety Information; Hydraulic Safety - Powermate PLS20825 Manual Del Operador

Important Safety Information

• Save all instructions
d. If fuel is spilled, do not attempt to start the engine but move the machine away from the area of
spillage and avoid creating any source of ignition until fuel vapors have disappeared.
e. Replace all fuel tank and container caps securely.
f. After refueling, replace fuel tank cap securely and wipe up spilled fuel.
g. Never store fuel or log splitter with fuel in the tank inside a building where fumes may reach an
open flame.
h. Never fill gasoline containers or the log splitter fuel tank inside of a vehicle or in a truck bed.
Accidental electrical static discharge can ignite fuel vapors which could result in serious
injury or death.
6. Never attempt to make any adjustments while the engine (motor) is running (except where specifically
recommended by the manufacturer).

HYDRAULIC SAFETY

1. The hydraulic system of the log splitter requires careful inspection. Wear eye protection and gloves prior to
inspection. Be sure to replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic
components.
WARNING
Hydraulic fluid may be under high pressure or be hot and can cause personal injury. Read, understand and follow the
following safety precautions.
2. Hydraulic fluid may be under high pressure or be hot and can cause personal injury.
3. Escaping hydraulic fluid can create a fire hazard and ignite if exposed to an ignition source.
4. Read, understand and follow the following safety precautions.
5. Check for hydraulic fluid leaks by passing a piece of paper or cardboard underneath or over the
area of the leak.
6. Do NOT check for leaks with your hand.
7. Fluid escaping from the smallest hole, under pressure, can have enough force to penetrate the skin resulting in
tissue damage and cause serious injury or death. Machine operation should stop until any detected
leak is repaired.
8. Seek professional medical attention immediately, (see page 11) if injured by escaping hydraulic fluid. Serious
infection or reaction can develop if medical treatment is not administered immediately.
9. Relieve all pressure by shutting off the engine and moving the valve control handle back and forth should it
become necessary to loosen or remove any hydraulic fitting.
10. Do not remove the cap from the hydraulic tank or reservoir while the log splitter is running. The tank could
contain hot oil under pressure which could result in serious injury.
11. Do not adjust the hydraulic valve. The pressure relief valve on the log splitter is preset at the factory. Only a
qualified service technician should perform this adjust.
OPERATION
1. Do not put hands near moving parts. Contact with the splitting wedge can amputate fingers and hands.
2. Never allow bystanders within 10 feet of the machine while running. Keep children and pets away.
3. Never operate the machine without proper guards, plates or other safety protective devices in place.
4. The engine and its exhaust system and the hydraulic system can become hot and can cause a burn.
Do not touch.
5. Towing Precautions:
a. Never tow the machine at speeds greater than 45 miles per hour.
b. Always refer to the vehicle owner's manual for proper towing.
c. Secure and lock the log splitter to the vehicle hitch before towing.
d. Verify the correct ball size of 2 inch is on the towing vehicle.
e. Ensure safety chains are correctly attached prior to towing.
f. Consult and comply with local or state regulations concerning highway use.
g. Do not carry passengers or allow them to sit or stand on the log splitter.
h. Avoid large holes or ditches when towing the equipment.
6. Exercise caution to avoid slipping or falling. Maintain a work space clean of wood and debris.
7. Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect.
8. If the machine should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause.
Vibration is generally a warning sign of trouble.
9. Stop the engine (motor) when leaving the operating position, and when making any repairs,
adjustments and inspections.
Questions? Call Toll Free at 1-800-737-2112
(Continued)
ENG - 4
Copyright © 2018 MAT Engine Technologies, LLC