Features And Specifications; Power Output - Jensen POWER 400 Manual De Instalación Y Operación

POWER Amplifiers

Features and Specifications

Your new Jensen Power mobile stereo power amplifier is the amplifier of
choice for the high demands of auto sound reproduction. With its deep-bass
reproduction and plenty of reserve power, low harmonic distortion and neutral
reproduction, the Power series of amplifiers takes Mobile Hi-Fi to new heights.
Like all Jensen products, when it comes to accurate sound reproduction the
Power series takes a back seat to no one. Jensen will bring your Hi-Fi
experience to new heights with the following features:
• MOSFET Power Supply
• High Current Bi-Polar Output Transistors
• Optimized Class B Design Minimizes Distortion and Reduces Idle Current
• Easily Drives 2-Ohm Loads
• Pass-Thru RCA's
• Variable Bass EQ 0 - 12dB @ 45 Hz
• 12dB / Octave Low Pass and High Pass filters
• Variable Input Level 400mV - 5V
• Short Circuit, DC-offset and Thermal Overload Protection Circuitry
• Diagnostic LED's - Green: Power, Red: Standby / Fault
Power 400 / 760 / 880 / 920
• Low Pass Filter 40 - 300 Hz
• High Pass Filter 40 - 300 Hz
• High Pass / Low Pass / Full Range Selector Switch
• Stereo / Mono Mode Switch (Power 400 and 880 only)
• 2/ 3 / 4 Channel Mode Switch (Power 760 and 920 only))
Power 900 / 1050
• Mono Subwoofer Amp
• Low Pass Filter 40 - 240 Hz (Power 900)
• Low Pass Filter 40 - 150 Hz (Power 1050)
• Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900)
• Subsonic Filter 15 - 55 Hz, 12dB / octave (Power 1050)
• Remote Input Level Control (Remote Bass Control) w/ 5 Meter Interface
Cable
Specifications
Power 400 / 760 / 880 / 920
• Load Impedance: 2 / 4-Ohm
• Signal to Noise @ 1 kHz: >100dB (rated power)
• Channel Separation @ 1 kHz: >60dB
• Frequency Response: 5-60 kHz, -3dB
• Input Impedance: 20 kHz, nominal
• THD+N @ 5 Watts: 0.02%, 1 kHz, 14.4VDC
Power 900 / 1050
• Signal to Noise @ 120 Hz: >100dB (Rated Power)
• Channel Separation Not Applicable
• THD+N @ 5 Watts: 0.02%, 125 Hz, 14.4VDC

Power Output

RMS Power Output @ 2% THD+N, 1kHz, 14.4VDC
Power 400
• 75 x 2 Watts, 4-Ohm
• 100 x 2 Watts, 2-Ohm
• 200 x 1 Watts, 4-Ohm Bridged
Power 760
• 75 x 4 Watts, 4-Ohm
• 100 x 4 Watts, 2-Ohm
• 190 x 2 Watts, 4-Ohm Bridged Stereo
Power 880
• 135 x 2 Watts, 4-Ohm
• 220 x 2 Watts, 2-Ohm
• 440 x 1 Watts, 4-Ohm Bridged
Power 900
• 300 x 1 Watts, 4-Ohm
• 450 x 1 Watts, 2-Ohm
Power 920
• 100 x 4 Watts, 4-Ohm
• 140 x 4 Watts, 2-Ohm
• 230 x 2 Watts, 4-Ohm Bridged Stereo
Power 1050
• 350 x 1 Watts, 4-Ohm
• 525 x 1 Watts, 2-Ohm
Specifications subject to change without notice.
2