Chamberlain CLLP1 Instrucciones Del Propietario

INSTALLATION
1. Open your garage door and park your vehicle outside of the garage.
2. Determine the mounting location on the ceiling and fasten the parking assist
using screw and anchor (Figure 1).
3. Depress tabs under the wires and temporarily remove the white and white/
black safety sensor wires from the garage door opener.
4. Stripping the wires prior to installation:
Installing one parking assist: Separate white and white/black wires and strip
7/16" (11 mm) of insulation from parking assist wires.
Installing two parking assists: Cut 6" (15 cm) of wires from the end of one
set of parking assist wires for use as connection wires. Separate white and
white/black wires and strip 7/16" (11 mm) of insulation from both ends of
connection wire.
5. Connecting the wires to garage door opener:
Installing one parking assist: Twist like colored wires for parking assist and
safety sensors together. Insert twisted wires into quick-connect holes: white
to white and white/black to grey (Figure 2).*
Installing two parking assists: Separate white and white/black wires and strip
7/16" (11 mm) of insulation from the end of parking assist wires. Twist like
colored wires for parking assists, safety sensors and connection wire
together. Secure with wire nut. Insert connection wires into quick-connect
holes: white to white and white/black to grey (Figure 3).*
* Please refer to your garage door opener owner's manual for proper wire
installation.
SET UP AND ADJUSTMENT
1. Drive your vehicle into garage and park in the desired location.
2. Activate the parking assist by obstructing the path of the safety sensors. The
laser will emit a pulsing bright red beam (Figure 4). Aim the red beam to a
location on the dash or hood that can easily be seen while seated in the
driver's seat.
NOTE: The laser will shut off in 1 minute. If you are not finished adjusting the
beam and it turns off, simply obstruct the path of the safety sensors.
3. Sit in the driver's seat and confirm that you can easily see the location of the
red beam. This location is now your point of reference for parking your
vehicle. CAUTION: Do not stare directly into the beam. Repeat steps for
installation on optional 2nd laser accessory kit.
NOTE: Periodic adjustment of the beam may be required.
OPERATION
1. Open the garage door by activating the garage door opener and drive your
vehicle into parking space.
2. The red beam can be seen moving across the hood of your vehicle as you
drive further into the garage (Figure 4).
3. Stop the vehicle when the beam is positioned at the location you confirmed in
step 3 during SET UP AND ADJUSTMENT.
NOTE: The laser is activated every time you drive into your garage. The laser will
shut off in 1 minute. A residual reflection of the red beam from the windshield
may appear on walls or objects in your garage. When operating a vehicle, always
ensure that there are no objects on the floor of the garage or in the path of your
vehicle. The parking assist is not a substitute for safe parking practices.
TROUBLESHOOTING
If the laser does not emit a beam:
• Verify nothing is obstructing the safety sensors.
• Verify nothing is blocking the parking assist lens.
• Verify that connections are not reversed.
• Verify that all connections are secure.
• Confirm that the parking assist is aimed toward the garage floor.
• Obstruct the path of the safety sensors and look for the red spot on the
garage floor.
Please refer to your owner's manual for additional information on your garage
door opener and the safety sensors.
Laser Garage Parking Assist
To avoid eye INJURY or damage to product:
• NEVER point the laser at anyone.
• NEVER look directly into the laser beam.
• NEVER disassemble the laser.
• The parking assist is NOT a substitute for safe parking practices.
• Use of controls or adjustments, or the performance or procedures
other than specified can result in hazardous radiation exposure.
• ONLY for use on Chamberlain manufactured garage door openers.
WARNING: This product can
expose you to chemicals
including lead, which are known
to the State of California to
cause cancer or birth defects
or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov
CARTON INVENTORY
Anchor
Screw 6ABX1-1-1/4" Wire Nut
Figure 1
Figure 2
Parking Assist
Safety Sensor
Wires
Wires
Wire Nut
Figure 3
Safety
Connection
Sensor
Wires
Wires
Parking Assist
Wires
Figure 4
Models CLLP1 and CLLP1-P
Owner's Manual
CAUTION
CAUTION
ATTENTION
LASER RADIATION
DO NOT STARE INTO BEAM
RAYONNEMENT LASER
NE PAS REGARDER DIRECTEMENT
LE RAYONNEMENT LASER
Maximum power output: < 1mW @ 635 - 670nm
Puissance de sortie maximum: < 1mW @ 635 - 670nm
CLASS II LASER PRODUCT
APPAREIL AU LASER DE CLASSE II
This Class B digital apparatus
complies with ICES-003.
Parking Assist
Insert Into Appropriate Terminals
Red White Grey
Insert Into Appropriate Terminals
White
Connection
White/Black
Wire
Connection
Wire
Red White Grey
Parking Assist