Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Tools and Parts
Tools needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Measuring tape
■
Pencil
■
Masking tape or
■
thumbtacks
Scissors
■
No. 3 Phillips screwdriver
■
for 1/4 - 20 x 3" (7.6 cm)
bolts
Drill
■
3/16" (5 mm),
■
3/8" (9.5 mm), 5/8" (1.6 cm)
drill bits
3/4" (1.9 cm) hole saw
■
Parts supplied
For information on reordering, see the "Replacement Parts"
section.
NOTE: The hardware items listed here are for wood studs. For
other types of wall structures, be sure to use appropriate
fasteners.
B
A
C
H
J
A. 3/16 - 24 x 3" (7.6 cm) round-head
bolts (2)
B. 1/4 - 20 x 3" (7.6 cm) flat-head bolts
(2)
C. Washers (2)
D. 3/16" (4.8 mm) toggle nuts (2)
E. 1/4" x 2" (0.6 cm x 5.1 cm) lag
screws (2)
F. Sheet metal screws 5/32" x 5/16"
(0.4 cm x 0.8 cm) (2)
G. Power supply cord bushing (1)
H. Damper assembly (for wall or ro
venting)
J. Exhaust vent cover (2)
NOTE: Depending on model, grease filter and charcoal filter may
be combined.
INSTALLATION REQUIREMENTS
Diagonal wire cutting
■
pliers
Stud finder
■
7/16" (1.1 cm) socket
■
wrench (or box wrench) for
1/4" x 2" (0.6 cm x 5.1 cm)
lag screws
1
⁄
" (3.8 cm) diam. hole
1
■
2
drill bit for wood or metal
cabinet
Keyhole saw
■
Caulking gun and
■
weatherproof caulking
compound
Duct tape
■
D
E
F
G
Not Shown:
Mounting plate
■
(Located on the
upper polyfoam)
Grease filters
■
Charcoal filters
■
Materials Needed
Standard fittings for wall or roof venting. See the "Venting
Design Specifications" section.
Location Requirements
IMPORTANT: Check the opening where the microwave oven will
be installed. The location must provide:
Minimum installation dimensions. See the "Installation
■
Dimensions" illustration.
Minimum one 2" x 4" (5.1 cm x 10.2 cm) wood wall stud
■
and minimum 3/8" (9.5 mm) thickness drywall or plaster/lath
within cabinet opening.
Support for weight of 150 lbs (68 kg) which includes
■
microwave oven and items placed inside the microwave
oven and upper cabinet.
Grounded electrical outlet inside upper cabinet. See the
■
"Electrical Requirements" section.
NOTE: Some cabinet and building materials are not designed
to withstand the heat produced by the microwave oven for
cooking. Check with your builder or cabinet supplier to make
sure that the materials used will not discolor, delaminate, or
sustain other damages.
Special Requirements
For Wall Venting Installation Only:
Cutout must be free of any obstructions so that the vent fits
■
properly and the damper blade opens freely and fully.
For Roof Venting Installation Only:
If you are using a rectangular-to-round transition piece, the
■
3" (7.6 cm) clearance needs to exist above the microwave
oven so that the damper blade can open freely and fully. See
"Rectangular to Round Transition" illustration in the "Venting
Design Specifications" section.
3
Publicidad
Tabla de contenido
