Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

MODEL: PFS16
CLEANING
Avoid using solvents when cleaning plastic
parts. Most plastics are susceptible to
damage from various types of commercial
solvents and maybe damaged by their use.
Use clean cloths to remove dirt, dust, oil,
grease, etc.
!
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products,
penetration oils, ect., come in contact
with plastic parts. Chemicals can
damage, weaken or destroy plastic
which may result in serious personal
injury.
COLD WEATHER OPERATION
For cold weather operation, near and below
freezing, the moisture in the air line may
freeze and prevent tool operation. We
recommend the use of air tool lubricant or
permanent antifreeze (ethylene glycol) as a
cold weather lubricant.
CAUTION:
Do not store tools in a cold weather
environment to prevent frost or ice
formation on the tool's operating valves
and mechanisms that could cause tool
failure.
Quick
coupler
Air hose
Quick
connector
10
HTTP://WWW.FREEMANTOOLS.COM
RECOMMENDED HOOKUP
1.
The air compressor must be able to
maintain a minimum of 60 psi when the
tool is being used. An inadequate air
supply can cause a loss of power and
inconsistent driving.
2.
An oiler can be used to provide oil
circulation through the tool. A filter can be
used to remove liquid and solid impurities
which can rust or gum up internal parts of
the tool.
3.
Always use air supply hoses with a
minimum working pressure rating equal to
or greater than the pressure from the
power source if a regulator fails, or 150
psi, whichever is greater. Use 3/8" air hose
for runs up to 50' and use a 3/8" quick
coupler on the air hose.
4.
Use a pressure regulator on the
compressor, with an operating pressure of
0-125 psi. A pressure regulator is required
to control the operating pressure of the
tool between 60 and 100 psi.
CAUTION:
The air compressor must be able to
maintain a minimum of 60 psi when the
tool is being used. An inadequate air
supply can cause a loss of power and
inconsistent driving.
!
WARNING:
Do not connect with an air compressor
which can potentially exceed 200 psi. As
tool may burst, possibly causing injury.
Quick
Filter
Oiler
connector
Compressor
Quick
Regulator
coupler
1-888-669-5672
MODEL: PFS16

TROUBLESHOOTING

!
WARNING:
Stop using tool immediately if any of the following problems occur. Serious personal
injury could result. Any repairs or replacements must be done by a qualified service
person or an authorized service center.
PROBLEMS
POSSIBLE CAUSE(S)
O-rings in trigger valve housing are
Air leaking at the
damaged.
trigger valve area.
Air leaking between
1.Loose screws in housing.
the housing and nose.
2.Damaged O-rings.
3.Damaged to bumper.
Air leaking between
1.Loose screws.
the housing and cap.
2.Damaged gasket.
Tool cannot work.
1.Nail jammed in the nose.
2.Low nails triggering anti-dry-fire
mechanism.
3.Dirt in nose piece.
4.Damaged or jammed magazine
prevents feeding nails.
5.Inadequate air flow.
6.Worn O-ring on piston or lack
of lubrication.
7.Damaged O-ring on trigger valve.
1.Inadequate lubrication.
The tool has a loss
2.Insufficient air supply.
of power or can not
3.Tool is not set up correctly.
drive the nail enough.
1.Incorrect fasteners.
2.Damaged fasteners.
Fasteners are jammed
3.Magazine or nose screws are loose.
in the tool.
4.Driver is damaged.
!
WARNING:
Only use Freeman authorized repair parts. For questions please call 1-888-669-5672 or
visit our website at http://www.freemantools.com
WEARABLE PARTS
Repair parts can be ordered from our website: http://www.freemantools.com
HTTP://WWW.FREEMANTOOLS.COM
CORRECTIVE ACTION
Replace o-rings on trigger valve.
Check operation of Work Contact
Element (WCE).
1.Tighten screws.
2.Replace O-rings.
3.Replace bumper.
1.Tighten screws.
2.Replace gasket.
1.Clear the jammed nail.
2.Load more nails.
3.Clear drive channel.
4.Replace or clean magazine.
5.Verify adequate air supply.
6.Replace and lubricate o-rings.
7.Replace trigger valve kit.
1.Lubricate the tool.
2.Verify adequate air supply.
3.Adjust the DEPTH ADJUSTMENT
wheel, or remove NON-MARRING
pad.
1.Verify that fasteners are the correct
size.
2.Clean and replace fasteners.
3.Tighten screws.
4.Replace driver.
11
1-888-669-5672

Publicidad

Tabla de contenido
loading

Tabla de contenido