Parts List - ENFORCER SD-7202GC-PEQ Manual De Instalación

ENFORCER Pushbutton Request-to-Exit Plates
Models:
SD-7202GC-PEQ
• Large illuminated "PUSH TO EXIT" button
• Language easily changed to Spanish or French
• Colored 12-inch wire leads with easy-to-attach
spade lugs for fast installation
SD-7223GW-LQ SD-7202GC-PTQ
Same as SD-7202GC-PEQ, but Same as SD-7202GC-PEQ, but
with white plastic faceplate with additional timer (1~180 sec)
and buzzer output
Specifications:
Model SD-7202GC-PEQ
Operating voltage
Current rating 10A@250VAC
Faceplate Brushed stainless
Operating temperature
Built-in timer
LED status indicator No
Dimensions
Weight 3.7-oz (105g)

Parts List:

1x Request-to-exit plate 2x Wallplate screws
1x Installation manual 1x Spare LED bulb
1x Resistor for 24VDC 2x Replacement message plates
(SD-7623-GSTQ only) (Spanish, French)
Changing the Message Plate:
Note: This should be done before connecting
any wires.
1. Carefully twist the switch and bulb assembly
counterclockwise about 20° (see Fig.1), and
then pull it out of the black tube (see Fig. 2).
2. Insert the blunt end of a small tool or rod (e.g., a
3
screwdriver or pen, ~ / " (10mm) diameter) into
8
the black tube (see Fig. 3). It should slide in
easily all the way until it contacts the inside of
the front lens/message plate assembly. Push
the lens/message plate assembly with your tool
until it pops off (see Fig. 4). Be careful not to
lose the spring.
3. Take off the transparent green lens and insert
the desired message plate.
4. Check that message plate orientation is correct.
5. Snap the lens assembly back on and replace
the switch/bulb assembly.
2
• LEDs Give over 50,000 hours of illumination
• Includes stainless-steel single-gang plate
(except SD-7223GW-LQ, which is white plastic)
SD-7623-GSTQ
Same as SD-7202GC-PTQ, but
with additional customizable LED
status indicator
SD-7223GW-LQ SD-7202GC-PTQ
12 or 24VDC
3A@24VDC
White plastic Brushed stainless
-40°~167° F (-40°~75° C)
No Yes
No No
4½"x2¾" (11.4x7.6 cm)
2.2-oz (62g) 4.7-oz (133g)
Colored leads:
5x (SD-7202GC-PEQ)
5x (SD-7223GW-LQ)
2x (SD-7202GC-PTQ)
2x (SD-7623-GSTQ)
Figure 2
Figure 1
Threaded
housing
Switch and
bulb assembly
Figure 3 Figure 4
Message
PUSH
TO
Plate
EXIT
PUSH
Transparent
green lens
SECO-LARM U.S.A., Inc.
Also Available from SECO-LARM
Pusbutton RTE Plates
Different sizes and button types available
SD-7201GC-PEQ / SD-7103GC-PEQshown
SD-7623-GSTQ
Electromagnetic Locks
80, 300, 600, and 1200-lb holding force available
Yes
5.1-oz (144g)
E-941SA-1200 shown
Fail-safe or fail-secure available
Switch and
bulb assembly
SD-997B-GBQ shown
Wireless Video Door Phone
With lightweight portable monitor
Additional monitors available (up to 3 total)
SECO-LARM U.S.A., Inc.
ENFORCER Pushbutton Request-to-Exit Plates
®
Indoor and outdoor, single-gang and slim-line
Electric Deadbolt
DP-236Q
:
No-Touch RTE Plates
SD-927PKC-NEQ / SD-9163-KSQ shown
Electric Door Strikes
Fail-safe or fail-secure available
SD-995C / SD-994C shown
RF Remote Control
Complete line of transmitters and receivers
SK- 910RBQ / SK-919TP4J-NUQ shown
Access Keypads
Indoor and outdoor
with and without proximity card reader
SK- 2323-SDQ / SK-1123-SQ shown
11